Could some one explain me the big differences between those two references ? except a small power diff.(5W), the shaft diameter (3mm vs 3.17mm)i only see the shaft length.
About his lenght i don't understand why it is so long except to bend it easier ...
Some one to take me of the dark ?
Now, has anyone tried to use it with a 2S battery and what could be a correct propeller association for how much max. thrust ?
Turnigy L2210-1400 Bell Style Motor
Kv: 1400 rpm/v
No load Current: 1.1A
Max Current: 24A
Max Power: 210W
Shaft Size: 3mm
Shaft Length: 28mm
Dimension: 28mm x 17mm
D2826-6 2200kv Outrunner Motor
Voltage: 2S~3S (7.4v to 11.1v)
Max Current: 21A
Suggested Prop: 7x4(3S) ~ 9x4.7 (2S)
Mounting Hole Bolt Circle: 16mm or 19mm
After major crash last week (loss of radio) I had to swap out the bent Turnigy D2826-10, had the spare L2210-1400 so it went in. Flies just the same as with the D2826-10 motor, much better than stock brushed 480 motor, no difference (as you would expect 205w v 210w motor same diameter). Video of the flight test (in windy conditions), take off was pretty ordinary and landing was a bit irregular :) :)
3.5mm is correct. They're your standard size connectors. I've got this motor on a CTH Assassin and it absolutely rips! It's a great buy just stay on top of the allens, you might want to use some locktite.
Hi can someone tell me if a Turnigy 2210/1400kv motor will replace the 2812/1400kv motor that broke a propeller shaft on my FPV Raptor after a dodgy landing. I was told at the hobby store that they can't supply replacement shafts. Thanks Trevor
I wouldn't. It's not going to have the same torque because It's a smaller diameter (22mm Vs 28mm) and the magnets are also shorter (10mm vs 12).
If in doubt always check the KV, the rated power (or at least the rated current) and the motor weight. Generally if the KV and weight are similar then you'll get away with it. In this case the only box ticked is the KV. This motor is too small and won't generate as much power.
WOOps! my mistake. I didn't read the spec'. I only read the label!
The can diameter is 28mm and the can length is 12 so it should be about right. BUT I still think that the magnets are only going to be 10mm long.
Check the weight of your old motor. I suspect you'll find that this one is lighter (therefore has less armature and magnet in it.
Just some findings after 50 or more flights, mostly on a 8x6 gws dd prop, so far the best combo for a ten foot liftoff and 40% throttle cruising. Attached to a 980mm Cessna converted to a grass taildragger.
What's up meter
8x4 3 blade gws 16amps 185 watts
8x6 2 blade dd 19.8amps 222 watts
9x5 3 blade gws 22amps 242 watts
9x5 2 blade dd 22.4amps 251 watts
Motor windings looks good and sounds great with the 8x6, some good vertical but not unlimited, planes weighs 650 grams... Ands it a Cessna, lol. Great motor, highly recommend . Cheers from Canada
Yes they can be changed out and quite easily. You will just have to use a bit of finess (careful handling) so as not to damage anything. ALWAYS be careful of the wiring, because the leads are tiny! If you search around, you can find 3mm. shafts on various sites and some have several in a pack for about the same price.
if you have old unused CD-ROM drive (for PC), you can get 3 mm stainless steel shaft for free.
much stronger than original shaft.
2 thumbs up!
Fantastic motor for the price, I love the Turnigy products and using them in all my models, these 1400kvs outrunners are just the thing to replace my old 1250s in my Zero & Corsair Fomies. Beautiful motor with unlimited vertical, 15pcnt throttle and they take off from my hand, thanks HK for such products
5 comments. Reply..
1 thumbs up!
As previously stated, a great motor for the price! These are not to be confused with the similarly sized Emax CF 2812 motors as there is a subtle difference. The Emax has a stator length of 10.1mm where as this L2210 has a stator length of 10.4 and therefore more wire length on the windings. My bench test showed 17.3A on a 3s LiPo with an APCe 7" x 6" prop and there is still a bit in hand as the motor only gets luke warm. I'm using this setup in my lightweight Funjet (AUW 12.5ozs) and it provides quiet, unlimited vertical performance. Thanks HK!
No comments. Reply..
3s 1800 30 rhino pille el yapmı modelimde kullandım.ısınması var esc 35 a kullandım ancak tam gazda performans kaybı yaşamadım.esc yi sağlam tutarsanız sorun yaşamazsınız.7x6 apc kullandım pervane.2 s te 8x6 apc tavsiye ederim.sf tarzında pervanede ideal olur.ısınma düşer.kırımsız uçuşlar..Thanks hk.:)
No comments. Reply..
Fantastic performance from such a small motor. With a 10x5 prop, it pulls my 550g 3D foamie with more than enough power for every possible stunt. Excellent machining, bearings, etc. Have already ordered 2 more.