|
7/3/2010
dukepapas (34%)
i need extra shaft for this motor add me please the link
|
|
|
 |
|
|
 |
|
1/4/2010
Blumm (82%)
What type os connector this motor use to the speed controller? Its better solder this wires instead of connectors? Thanks!
|
|
|
| |
|
masf01
(25%)
Hello,
It comes with 3.5mm male golden connectors installed and a set of females plugs (3.5mm) to solder on the speed controller. Personally I do not like soldering the wires directly.
Regards,
Marco
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
12/28/2009
hillflyer (42%)
My Tr 2826b 1350KV pulls about 1 Amp without a prop at 10 Volts. I think this is too high. Also the stator gets quite warm after a minute of running without load. What are your experiences?
|
|
|
|
|
|
|
|
|
6/16/2009
specr (61%)
3.2...
|
|
|
|
|
|
|
|
Keith (76%)
is this a good motor for 3D, if so what is a good 3s setup?
|
|
|
|
|
|
|
|
|
Ernesto (67%)
Sorry. The page where you could see the shat is w w w .hobbycity.c o m/hobbycity/store/uh_viewitem.asp?idProduct=6485
|
|
|
|
|
|
|
|
|
Ernesto (67%)
The question above relates also to the Turnigy AerodriveXp 28-26 Shaft and the grooves and the cutout could be seen at the page ****hobbycity****/hobbycity/store/uh_viewitem.asp?idProduct=4908
|
|
|
|
|
|
|
|
|
Ernesto (67%)
This 3,17 mm diameter shaft has two grooves for fitting snap rings. The center groove is used in the original assembly of the motor with shaft projected to the inner stator side of the motor. The cutout in the other side of the shaft is to position the locking screw of the outer rotor for this original assembly. For using the 317MPRPSVR 3.17mm Prop Saver w/ Adapter to the rotor side, the snap ring has to be disassembled from the center groove and instaled in the end groove. But in this assebly there is missing a second cutout more certer positioned because the outer rotor screw lock would be located more to the center of the shaft. Would you ask the manufacturer to change the design to add this second cutout?
|
|
|
|
|
|
|
|
|
Jeffrey (34%)
what is the diameter of the motor?
|
|
|
| |
|
John
(88%)
28mm diameter
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Hans (50%)
What is the max current for this motor
|
|
|
| |
|
John
(88%)
You can go to 15 amp safely without killing the motor.2s lipoly with a 8*4 apc or 3s with a 7*6 apc.These are good reliable combinations.Plane weiging about 500/600grams.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
twiztidbowler
(84%)
This motor works great with a APC 8x6SF prop on 3 cells with a 18amp speedcontrol
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Keith
(76%)
Will it do well in a 3d plane like a shockflyer?
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
RICKSTERHELI (34%)
DOES THIS MOTOR COME WITH PROP ADAPTER THAT MOUNTS ON THE SHAFT?
PICTURE SHOWS A REAR "CAN" MOUNTED PROP ADAPTER..
WHICH ONE CAN I REQUEST TO COME WITH THIS MOTOR - THANK YOU !! FROM RICK IN SUNNY FLORIDA...
|
|
|
| |
|
John
(88%)
No prop adaptor is supplied to suit shaft at front.You will need a 3.175mm prop adaptor
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
Rush! (66%)
is the shaft 3mm or 3.17 as reported in the reviews? please confirm. thanks.
|
|
|
| |
|
John
(88%)
Shaft is 3.175mm
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
