|
|
|
|
Not very precis.
See the video below. Unfortunately I did not have a HXT500 in stock to compare. The 1440A do not show the small mouvements.
http://www.dailymotion.com/video/xboez2_hxt900-vs-turnigy-1440a_tech
In the futur I will bought only HXT500
42 people like this review.
|
|
|
| To high deadband (measured deadband is greater than +/-10us, in total the deadband is 20us "wide"). That is too high and not good for a precise servo. You will have problems when you want to trim your model - small stick movements will be "ignored". HXT-500, HS-50 or D47 performs MUCH better.
28 people like this review.
|
|
|
| Just got 4 of these Turnigy servos, and I think they are the best <5g/<$4 servos here. Case feels much sturdier, and it has SCREWS holding it together! Same speed as other servos this weight but seems to have more power and better resolution. Current draw at 5v- centered, around 6ma, about 100ma when wiggling it, 400ma when stalled. Weight is 4.9g. Note that this page used to be for the Power HD 4.4g servo, many of the old reviews are for those!
14 people like this review.
|
|
|
| somewhat similar to the em 4.3g servo. i did not find that this servo has higher holding torque than the em as specified (0.6 vs 0.5), but are almost the same. they are both really tiny and this one seems a little better built than the em.
5 people like this review.
|
|
|
| Have six of these mounted in small foamies. Very satisfied. Wire lead length is 4-7/32"(including connector). Weight including wire, one servo arm & screw is 4.8 g.. Great little servo for the money!
4 people like this review.
|
|
|
| Nice little servo. Got 4 of them, all work great.Fast good centering and strong.
2 people like this review.
|
|
|
| I havce used these on a stevens aeromodel Diddlerod. Servers have good tourque and solid build quality so far. Resolution is adequate for indoor flyers.
2 people like this review.
|
|
|
| Von 5 Servos rutschte bei einem das ritzel auf dem motor durch, liess sich beheben. Bei dem Preis kann man nichts falschmachen.
2 people like this review.
|
|
|
Good but not excellent, the price is rewarding.
Ok for indoor planes.
1 people like this review.
|
|
|
Hi all, I bought 6 PowerHD 4.4g and installed on e-flite minipulse. They fit ok and work ok with no jittering, precise zero point, controlled by a DX7 rx AR6100 dsm2.
Buoni microservo, installati senza problemi di precisione o affidabilita'.
1 people like this review.
|
|
|
| works well with EP200 frame with some mods, e.g., filling to enlarge the servo mounting holes.
1 people like this review.
|
|
|
| i use these on my firefox ep200 all around. this is just the ticket. Don't bother buying those expensive servos, this would do the job nicely. Fast, Simple to install, only a very small amount of mod on the frame. Don't bother with the hxt500 for your firefox ep200 this would be the perfect servo for it. I am buying another 9 more of these. They are so cheap!!
1 people like this review.
|
|
|
| I am pleased with these. They respond to small movements and a requieter than other servos of this size. If you remove the bottom section of case you can fit these into the Flycam One 2 servo base - better than the servo supplied here!
1 people like this review.
|
|
|
NOTE: torque on the box states only 0.8kg/cm NOT 1.0kg/cm as advertised here.
Can be stripped to reduce the weight down to 4.0g with dual arm servo horn by removing case.
Otherwise seemingly good servo.
1 people like this review.
|
|
|
| Seems to be a good servo. Bought three and all work fine. They come with four different arms, two mounting screws that don't fit, and ONE screw to attach the arm to the servo. the servo arm fits rather loosely on the servo compared to other servos and won't stay on without that screw so don't lose it! Weight of the servo with a servo arm and all of the screws is 4.9g (call it 5). Wire length is just over 9cm not counting the connector. Others are saying the servo is held together with screws but I see none, seems to me like it's a snap together servo. The thing that holds the arm on (I think it's called a spine?) has a dia. of 3.5mm and 22 'teeth' if I counted right. Previous reviewers were saying that the servo has a very small number of steps and the dead band is to tight, but I think that the servo is fine for what it should go on. Sure, it probably is terrible for a really good 3D plane or some kind of mini outdoor pylon racer but you shouldn't buy a few dollar servo for those planes anyways! I think it's a great servo for what it should be used for. I'll be putting mine on a balsa flying wing (20") that flies at a moderate speed and has very small control throws. The wing is called a 'Topic' and was designed by Paul Cook.
1 people like this review.
|
|
|
| a ver como se conporta en mi proximo f3p |
|
|
nice litlle Servo
use it in foamies |
|
|
| trs bon servo tester sur un belt cp rien dire pas de difference avec les servo d'origine |
|
|
| very good for litle helis,100 - 200 size,they're not NASA prescise but think of the price,and size...veru good...i only had one issue,i had to increase the travel adjust a litle bit,they didnt give enough cyclic,after adjustment it was ok! |
|
|
| habe sie im EP 200. gut und billig |
| Click here to see all reviews |
5 crowns 
30/12/2009
29/12/2009
26/10/2009
3/12/2009
