Turnigy 2627 Brushless 300-Size Heli Motor 4200kv

 Runping 70 points

Oh, my comes with pinion and banana connectors.

 Runping 70 points

in detail, it comes with 12t and 13t pinions each, but not motor mount.

 Runping 70 points

No prop adapter too. Does HK already know I am going to use this on a heli?

 Selwyn 3 points

I got mine all balanced. So i didnt remove anything or add anything. You can use it just the way you get it.

 Augusto 3 points

Hi, what pinion do you use? I'm buying this for my hk 250 gt, and I have a 25A ESC (hope this fit good).

 Adriaan 2 points

I took a hex driver with a 2mm shaft and cut it to the right length. Tool-steel is much better quality than the stock shaft-steel

 PeteDee 182 points

The shaft is 2.3mm

 cofl1001 12 points

Hi, You can try the Rhino 1050mah battery, any 18A ESC and for pinion this one has the right inner diameter, but is only 12T: www.link

 Tiago 9 points

Galera nao gostei deste motor para Zagui 1 metro muito fraquinho vou colocar um para classe 600 de heli!!

 DanielW 41 points

not really you need a lower KV motor unless you got a small multi-rotor but then these would be to heavy!

 DarrenH 470 points

I have mine in a trex250 flybarless and its a good fit and plenty of power

 nickgnz 11 points

I have run 2 in a boat on water jet drives *******youtu.be/rWzRAPzeu8M They have very high RPM iseal for a 18mm water jet, I would think you would need a reduction gear for a plane unless its an EDF

 Juraj 2 points

In mine was a couple pinions, connectors and shrink tubing...yet no X mounting plate or the prop adapter as picture says. Delivered this week

 dean420 68 points

no to big try a smaller motor

 tonyastro 11 points

No, too heavy/powerful. You need one that's good for 2 cell.

 dean420 68 points

2.3mm 10PC e-clip (2.3*0.4) 110BS, A2016T, A2029 AND A2035

 Kevnorm 12 points

So 2,5 mm will not fit? I measured and seems to be 2,7 mm. Is it possible?

 dean420 68 points

they should fit tight mine uses 2.3mm

 Oleg 3 points

Where are you going to use the motor? To install a 250 X mounting board is not required. If the aircraft can get the shaft with the aid of heat, and then use a prop Saver. sorry for my english)

 Pengyuan 1 points

I didn't get the mounting plate or the other silvery thing too. Also no screws were included.

 StevenC 556 points

I had to do a small modification to the HK250 motor mount. I just enlarged the hole a little. AAlso, the shaft is too long to fit in the 250, you need to dremel cut 5mm off it.

 VTCCU 84 points

thanks StevenC, i've enlarged the mount , wasn't sure about how many mm to cut!!

 dean420 68 points

it fits tight. i cut the shaft down a bit with a cheap cut off attachment in a drill, just cover the motor vents with tape first so you don't get little metal bits in the magnets.

 dean420 68 points

and I dont think this motor came with a pinon I bought one

 Kevnorm 12 points

it came with two...

 dean420 68 points

how many teeth?

 dean420 68 points

ya mine didn't come with any just checked my unboxing video but I use this one with great results

 dean420 68 points

www.link

 dean420 68 points

well just search 0.4 pinion in the hk search and its the 13t

 Kevnorm 12 points

I got one with 12T an one with 13T. It must be 0.4 or?????

 Kevnorm 12 points

I didn't get any screws with this. someone know the dim of the screws. it's two different dims...

 dean420 68 points

from what i read the pinions that come with this motor dont work well with the hk-250 but as i dont have the stock pinions thats as much as i can help

 dean420 68 points

I would go with a 20c 30c if you want a bit more power Heli rotor: 205mm for a plane try buying a couple different sizes from 4x4 to around 6x4 they are cheap and then you can see what works best for your setup

 Tiago 9 points

try propler 4.5x4.5 for more speed ou 6x5 low peed.

 Napstr 686 points

As the jst plugs are only rated to around 6 amp I would replace them to run this motor as although they will handle it there will be a voltage drop through the jst plug at the amps this motor runs

 flash242424 568 points

Sim é* excelente para o 250GT com pinhao 12T fica com muita potencia e rapidez bom mesmo

 Helimaniacos 899 points

sim, muito bom, estou usando ele no meu 250gt com o pinhao original de 15t

 LEONARDO 26 points

qual ESC seria o Ideal para este motor ?? vou usa-lo no Walkera Master CP classe 200. Obrigado

 MartinP80 1 points

Yout need a Modul 0.4 Pinion for 2.3mm shafts, that is available here. I think 12T is fine, maybe 13T will give you a better Headspeed.

 flash242424 568 points

Yes u are right u will need to buy one of this www.link

 FRNFRN 139 points

It comes with two pinions. A 9T and a 12T. Pinions' hole diameter is 2,2 mm and the shaft's is 2,3 mm.

 flash242424 568 points

I recommend that HK web developers implement functionality that would be not answer the question proposed to her and just disappear from the list of questions of our accounts, so we can do a better job. Could also be filtered the questions where the best answer already as been chosen. Unregistered users (Customer) should not be able to ask questions because they could not choose the best answer and give the 20c to someone.

 Helimaniacos 899 points

It comes with two pinions. A 9T and a 12T

 RandomBob 24 points

15t pinion is too much for this motor on the 250gt. use the 12t pinion

 FRNFRN 139 points

Thanx RandomBob, and what's your opinion about the 9T?

 RandomBob 24 points

****

 Helimaniacos 899 points

i using 15T pinion, but reduce throttle curve

 flash242424 568 points

Yes 12t its perfect for 250gt i use one

 flash242424 568 points

I recommend that HK web developers implement functionality that would be not answer the question proposed to her and just disappear from the list of questions of our accounts, so we can do a better job. Could also be filtered the questions where the best answer already as been chosen. Unregistered users (Customer) should not be able to ask questions because they could not choose the best answer and give the 20c to someone.

 Vinger 13 points

No motor mount or prop adapter as pictured was delivered with mine. Got useless pinions instead!!

 Rodrigo 5 points

yes it is possible to put this engine in the Honey Bee

 David 46 points

Use the Esky EK5-0005 I think, had too much good lock with that one!

 flash242424 568 points

I use one on my old HBK2 it a 12T pinion it gave lots of power.

 flash242424 568 points

Stock updated frequently. No ETA,goods will arrive every 15-20 days

 suraki 41 points

Yep, you get everything as pictured.

 deanc 253 points

Only the motor mounting slots on the GT needs to be widened to accommodate the motor screws.

You may also need to shorten the shaft by about 2mm so that it won't hit the cyclics

 Pengyuan 1 points

Also the 250gt motor mounting screws are too small / too long for these motors.

 Shanti 108 points

No, too small! For a HK450 e.g. a 2215, 2836 or E500 would fit best.