Planes & Parts
Helicopters & Parts
Multi-Rotors & Parts
Cars & Parts
Boats & Parts
Bikes & Parts
Scale R/C Tanks
FPV & Telemetry
Batteries & Accessories
Chargers & Accessories
Robotics & DIY
Servos & Parts
Radios & Receivers
Gas/Glow Engines & parts
UBEC & Regulator
Hardware & accessories.
Clothing, Gift & Acc.
USA warehouse now open. Our USA warehouse is now open!
Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
HK F4U Corsair 1160x3 Replacement Propeller Set
Listing for 2pcs of 1160x3 propellers.
PRODUCT ID: 5J041
Length (Inch [X])
Pitch (Inch [Y])
Update/Add my own data
Does this fit the 1200mm FW190??
do the 11x6 work on the f4 corsair 800mm?
does this fit the Durafly F4U and P51?
no you cant use this with the duraflys 4 blade becouse if you want to have in this airplanes a 3 blade you have to decrease one inch in pitch and add one in the size. best regards
actually this should work with them both will be more efficient but may loose a little thrust
What would be a good 2 blade replacement for this 3 blade?
5 points - 3/24/2012
I got this for my t28. Had to drill out the hole and the hex shaft is to small. Tapered it with a knife and got it to fly ok. Must be a better prop some where For the Trojan but it's flying.
3 points - 1/28/2012
will it fit to HobbyKing YAK 54 Brushless EPO Plug-n-Fly :http://www.hobbyking.com/hobbyking/store/__13451__H
It's got a 4 mm hole. But you can always adapt it to a smaller shaft. To fit a bigger shaft you'll have to drill it out. In that case balance it again.
43 points - 12/26/2011
Its been forever for this product to be availible does anyone know when or where can i get them?
here and now
6 points - 2/22/2011
Will this fit the art tech brushless cessna 182 400 size?
Thank you :-)
This prop is great with the hexTronik DT700 Brushless Outrunner 700kv, wich is the same motor of the F4U Corsair from Art Tech. If your Cessna has this motor it will be fine, compare the weight and other spec with the HK Corsair
Thank you derfel, I have not received my plane yet, but i will check it when it arrives.
not with the same thrust. use apc style and u can use the original spinner
tnx Etto, do you know the prop size or know the type i should use?
if u had the cessna 182 skylane, brushless 980mm wingspan, u can use this propeler with exactly same results than www.link
I can't see the link, it only says ****link Is it on hobbyking? I can find the original online, but hobbyking is much cheaper. thank you Etto :-)
they cut my answer, its the gws 80-40 tree blades - take care to dont buy the counter rotate one...
BEST ANSWER CREDIT AWARDED
ok, thank you very much :-)
If it doesn't, you can make it fit in several different ways. Rule N 1 : get handy.
Is this for the mini 800mm F4U?
Noh this is for the larger 1000mm HobbyKing/Artech F4U
I hope so because that is what i found so far so i ordered two and ill let you know how they work.
Is this propeller useable for art-tech spitfire ?
Yes, it is the same propeller. I use it on my Spitfire
ok, thanks,but the spinner from Spitfire is also compatible with this propeller ?
Well, not really! (I have both, the Spit and the F4U) It is NOT the same prop! You will have to modify the spinner a little bit! But in the end it works! The Spit flies good with the F4U prop.
Yes, I had to modify the spinner
You must have an engine 700 kV, then the propeller can you use what you got engine??
Yes you can use this one for the Spitfire.
I ordered them and they fit.
keep on flying
I've just bought it, but others say that it's usable (that's why I bought it)