USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
The HK-310 is the new kid on the block at a break through price!
Featuring 2.4ghz FHSS technology, a huge 16 model memory, Detailed LCD Display, an array of user programable features such as Dual rates, EPA, Steering and throttle curves, ABS, timer and many more. The included 3ch HKR3000 Reciever has a bind button so you can say good bye to bind plugs for good!
Features: 16 Model Memory with user programable names 2.4ghz FHSS Technology Dual Rate EPA ST Curve TH Curve TH Hold ABS (Anti-Lock brake) Timer ATS (Automatic Start) BK Mix (Brake Mixing) Custom Mix Fail Safe Neutral Calibration HKR3000 3ch RX (Included) Detailed User manual
Hi everyone well have 1 of these and for the life of me I can not get it to work with the new Trooper I brought, can get the steering to work right to left but no forward or reverse have tried every combo and still no motor action, have read the manual over and over and the trooper manual the same and still can not get this this to work..
A two cell lipo is 8.4v fully charged. 8 AA batteries are 8 x 1.4v = 11.2v. Would a 3s lithium battery (such as PRODUCT ID: T2650.3S.1C) be too much? I notice this product is recommended for the Turnigy 9X transmitter which is also 8AA standard.
Can any one please help me, just got my new Turnigy Trooper SCT 4x4 1/10 Brushless Short Course Truck (ARR) and when I brought it this is unit they advise to buy with the car, but can not seem to get the trooper work.. the steering works but no motor action thanks inadvance for any help. rgds Chris
Try plugging everything in to your receiver and powering it up with the tx turned off (be sure to disconnect motor wires from esc or remove pinion gear to avoid runways) with the rx powered up turn on the tx then hit the bind button on the rx. The light on the rx should change from red to green to indicate correct binding. Hope this helps
Hey I want to get this transmitter and receiver but I was wondering do hobbyking sell a fuel tank that will fit a kyosho inferno mp7.5, because mine is leaking.
Has anyone experienced issues when using this radio with high speed digital servos, more specifically a savox 1257tg and a align ds610? Thanks in advance for the help.
Thanks Rafael, im from Portugal, are you to?
My Crawler have 2 steering servos, front and back, and does this transmiter do that? Like turn fornt only, turn back only, turn all 4 wheels....
yes joao this transmitter works in al rc models, but if you ara using a crawler maybe you need more funtions, but yes you can use this one, and its a very good transmiter and at a very good price¡*¡*
Had this tx for a few months a everything worked ok... Since today. Now, the steeing has gone wild, I'll try to explain : if I turn the steering wheel to the right, everything works perfect but if I turn to the left, first the servo turns left but if I keep turning the sw left and exceed half way, then then the servo returns to neutral then start to turn left a little. Of course I tried with another servo and another rx : same result. The problems comes from the tx and if I invert the steering channel on the tx, it does the same crazy thing in opposite direction. I have made a reset, re-binded to the rx : same result. So I just can't use this tx anymore. If someone has an idea, that would be great !!!
Hey, do you need to program this through a pc or is it ready to use? I really want to get this if it doesn't need to get programed through a pc, so does it needs to get programed through a pc? Or not? THANKS!!
hi I have a GM XG-6i 2.0 FHSS RACE SPEC 3-channel radio.
Specification
Frequency 2400 MHz
Modulation FHSS
It looks just like the HK-310
Does anyone know if i can use the HKR3000 receiver.
it says you can do a custom mix. does anybody have experiance doing this with this radio. looking to beable to do 4 wheel steering mixes for a clod buster for example. mixing with frt steering so that rear steering kick in at say over 50 percent drive channel and limiting the full throw of the slave c hannel or rear steering in this case. just currious any answers would be awesome
Considering the price.. I don't think so.. you probably can't get an LCD ( at a reasonable price ) even to "brand radios" - so go ahead and buy a new one *)
It doesn't un-screw from the body of the tx. It does appear to be in two pieces, but I am hesitant to try and take it off without looking inside the controller first.
not easy, if you open your tx, will see that antenna is hold in place with a circlip, easy to put off, BUT antena wire is soldered to tx board, so unless you are ready to unsolder the antenna cable and solder a new pigtail in place with a connector to be able to screw/unscrew antenna, there is no chance. So if you want it can be done but be ready to find an pigtail cable with connector, best chance is an old pc wifi card that become a donnor. cheers.
The antena is fixed in the body of the radio, but if you take of the board where the wire of the antena is solded, you have no problems. 'cause the board is not soldered but fix in an adapter
I've pointed out to HK before that as they stock cars in NL it might be clever to also stock TX/RX for cars there... I cannot believe they do not obey me! =)
I have this controller for my Turnigy Buggy, but the LCD display never worked. I have no idea how to program the settings. I don't really need to do any custom settings, but I don't know if I am missing out on anything important.
I just broke my steering wheel :-( I have glued it with CA but don't think it will last long....
Does anyone know if there is a replacement steering wheel ? As per reviews of replacement steering wheels in this site they are not suitable for this TX...
Appreciate any help on this.
Thanks
I had the same problem as you and I bought here in HK a new steering wheel in alloy, the only problem is that you will have to adjust a little plastic piece between the new wheel and the radio, but it isn't difficult, I hope this helps you!
Hi Alex.
Thanks for your answer. Till now the CA still holds bu when it won't longer do the job I will do so.... BTU - I am not sure it is the wheel itself... I think it is the shaft which I am no sure included in the alloy wheel kit.
Thanks
If still the CA holds the wheel, it's okay. But in my case was the plastic shaft broken and that is included with the new wheel, here you are the url of what I www.link includes 3 different shafts, and the first or the second of the left can be modified for it usin in our hk-310
You are welcome!
I can't post with my phone url, so you must look in radios&receivers, and there in part&accessories in the first page you will find the steering wheel, the silver ones
The HK-300 has simple features, and the HK-310 has more advanced configuration:
Features:
16 Model Memory with user programable names
2.4ghz FHSS Technology
Dual Rate
EPA
ST Curve
TH Curve
TH Hold
ABS (Anti-Lock brake)
Timer
ATS (Automatic Start)
BK Mix (Brake Mixing)
Custom Mix
Fail Safe
Neutral Calibration
Customer Reviews
Overall Rating
yasharizm
13 likes
Value
UNRATED
Quality
UNRATED
3 thumbs up!
hk still managed to surprise us. I can tell the monster truck will be very useful. Shipping in the process of product when you receive an extra box of 400gr I wish I could not control him.
Very nice radio , has all the same features as your big name brands.... Very impressed with quality for such s little price ... Performs very good on the water ... Very simple to program ... I have nothing bad to say about this radio ... It's a must have ... Way to go H.K
I am very pleased with this purchase.You will not find another radio in this price range with the features this unit has! I would consider this the best deal I have had to date with HK!!! Dont be affraid to pick one up! You will be very impressed with its performance and impressive list of features!!!
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg){kind=small}
.jpg){kind=small}
