Mni Drill Bit Set (14pc)

 waterlogged 2701 points

I'd be lost without the first two but how on earth do you use the smallest drills. My hair is thicker than those :-)

 anikeev 619 points

It's suited for mini and micro drill. They looks like a usual motor with collet at the end. First half of this set can be used in 1mm collet second half in 1.5mm collet (means collet wide open and max open is 1-1.5mm). I'm not a dremel user but seems that it's collet have a wider range so it's hard to tightly fix such tiny things.

 SamWitj 5 points

yes, if the collet and the drill chuck is available for small drill bits .

 Jiri 566 points

ne tohle urcite neni stainlesssteel!

 shay 2 points

no from steel

 SamWitj 5 points

ne tohle urcite neni stainlesssteel!

 Johanes 8 points

Opravdu to neni neni stainlesssteel...

 EmikBak 38 points

very good quality. bought one for myself

 Brain 110 points

Thanks for the info

 Kellyann 16228 points

Noobie yes I know. The pin chuck have been hard to get every since HK started selling the MINI BUTS. I would be nice to get one. The drills are very very small.

 Noobie 69 points

You're welcome brain. Kellyann, the pin chucks are in stock, just copy and paste the link I posted above it will take you there. I'm glad you like it EmikBak. It's the one I thought look a bit better than the others on there. I just need something for the servo holes which I tend to just force with the screw, but it's a pain to do usually.

 Kellyann 16228 points

Noobie thanks I will go and have a look.

 BernardoUruguay 259 points

I agree with you. It would be very useful. I´ll send an email to cs and see what happens

 Kellyann 16228 points

Good luck I think not

 rcsilent 14 points

if the chuck of the drillpres can take drillbits from .2 to 1.5 mm (.008" to. 063") should be perfect. I think that will be ok, just be really carefull with the smaller bits they are very fragil.

 Allison 1358 points

These drill will drill wood, metal, plastic, fiber glass and corean if you wish.

 Sally 659 points

Very good

 kadet 10 points

will drill a soft thin metal and wood

 Protoser 6 points

Only would drill thin metal sheet like a code can, else would be easy to break as they are quiet thin

 woodbpilot 143 points

I back ordered 3 of these**holding up an order. Anybody know when they were last in stock?

 Sweden 161 points

I have waited since 13/5 for 7pcs of this, my order worth 1055$ are on hold.

 srepfler 1119 points

Back in stock!

 Sweden 161 points

Waiting again, but now my order are only 921$. I have waited a while for it to arrive again, but still nothing. 25/10

 Sally 659 points

Hay it is in stock now

 Devon 5 points

you wouldn't want to use this with a dremel. these are used to drill out the shock pistons on a R/C car. you would want to use this with a pin wise

 Peter 1 points

you can when steady use it from 0.4 mm with a dremel, but check the collar for size. Anything under that size use with a pin-vise.

 Allison 1358 points

Jackrr the shafts are the same size as the drill size from 0.2 mm to 1.5 mm

 Bernardo 19 points

I've already used these drill bits (1mm was the minimum) with dremel 4000 and collet 1/32