Turnigy L2206A-1650 Brushless Motor (130w)

Total of 24 discussions.

Heli-Yeah!

10 points - 5/7/2013

I just received two of these motors to test on my V-tail, and they are labeled "120W" instead of the "130W" rating as stated on this page! Just a little FYI...

mhtpk

1 points - 3/23/2013

which one is the compatible with this motor 25c 05 mah or 20c 05 mah?

turgut

12 points

C rate is calculating with max current load, this means their both of two is compatible for your motor.

BEST ANSWER CREDIT AWARDED

turgut

12 points - 3/23/2013

is this motor compatible with 18-20 a esc?

Roger

2241 points

With a max current of 17.8A, use 20A or higher.

RON

1 points - 3/21/2013

CAN ANYONE TELL ME THE SPACING AND SIZE OF THE MOUNTING HOLES ON THIS MOTOR? I WANT TO USE IT IN AN EDF.

chris

1 points - 3/7/2013

hi... how do i connect this to the ESC? cant find any documentation on the wiring? which wire goes to A?... B?...C?

Roger

2241 points

Just connect the motor wires to the ESC wires, if it rotates the wrong direction, switch the connection of the two outer wires from the ESC, that should reverse the motor rotation.

shocking_guy

22 points

Roger, it is true that switching the two outer wires will reverse the motor... however, changing Any Two of the wires will do that. The reason is that a brushless ESC produces three phases which are each 120 degrees out of phase so it does not matter which two wires are switched...

Oliver

33 points - 2/24/2013

could i use a 3s, 8x4 with a 20AMP

Roger

2241 points

Yes you can.

Alan_L

55 points

Given the ratings directly above state MAX AMPS 17.8 I'd say you will kill it very, very quickly.

Dean Blair

23 points - 2/17/2013

does this come with the connectors pre-soldered?

QuadSB

424 points

Hi Dean, I bough 4 of these last july, and they came as pictured. Pre-soldered males on the motor leads and 3 pieces of female socket for your ESC's. Even three pieces of heatshirnk! Hope this helps.

BEST ANSWER CREDIT AWARDED

Dean Blair

23 points

Thanks alot QuadSB.

darkvaderz

118 points - 1/6/2013

ecalc.ch/

darkvaderz

118 points - 1/6/2013

Hi, one points = how much in cash??

QuadSB

424 points

1 cent I think. Credit me to confirm. :)

BEST ANSWER CREDIT AWARDED

darkvaderz

118 points

so?? loll

QuadSB

424 points

:) ten points = ten cents! thanks!

darkvaderz

118 points

cool XD

mathew72

42 points - 1/6/2013

hello is that I can put a 5 * 5 with a 2s lipo 1000mAh and controller 20 A thank you

QuadSB

424 points

Check out ECALCdotCH for a prop calculator that should give you some guidence with this. Hope this helps

BEST ANSWER CREDIT AWARDED

mathew72

42 points

thank you but I can not find it ECALCdotCH

QuadSB

424 points

Did you type it in your browser? Replace dot with a . WWW dot ECALC dot CH

mathew72

42 points

yes I look with my browser, but I can not find desoler for my English I am French

darkvaderz

118 points

***********ecalc.ch/

mathew72

42 points

thank you I just found

mathew72

42 points

What you advise me as propeller is a small 75 cm wingspan racer 300g

Skyler

8 points - 1/3/2013

Well 12x4.5 on 2s maybe I would try 11x4.7 rpm on 2s is 12210 3s rpm is 18315. I have this motor on a delta wing with a HK25A esc useing a 6x5.5 on 3s nano 850mah

darkvaderz

118 points - 12/30/2012

12x4.5 prop will fit on this motor or motor are to small?? for a quad... thanks!

Roger

2241 points

That prop is too big for this motor. If you want to use that size of prop, choose motor with slightly lower kv, around 750kv - 1000kv.

BEST ANSWER CREDIT AWARDED

Roger

2241 points

An 8x5 or 8x4.5 is best with this motor.

darkvaderz

118 points - 12/19/2012

can I use a 30a esc ??

QuadSB

424 points

Need at least 20A ESC's for these guys, I'm using Turnigy AE-30's and they don't get hot at all, they work great! Hope this helps!

BEST ANSWER CREDIT AWARDED

thinegod

2 points - 8/6/2012

Will this replace the motor used in the light aircraft 182? http://www.hobbyking.com/hobbyking/store/uh_vie
wItem.asp?idProduct=6331

Le_Biscuit69

5 points

Hello, I used this motor in a Fox 1.8m MotoGlider From Hype. Its weight battery included is next to 800g. With this motor, it climb almost verticaly. It's a real elevator ! lol And the best in this ? I was forced to block the throttle to 60pcnt because my ESC is to small. Hype MDM-1 Fox 1.80m Weight : ~800g Prop : Foldable 10x6 (default 9x5) Lipo 3S 1000ma/H - 1250ma/H - 2200ma/H Hope It will help you

davdi

31 points - 4/26/2012

Replacement shaft: KDS-22-S (it fits better to L2210, due to motor length)

kidracer15

3 points - 4/20/2012

What Lipo should i use for a Xcopter with 9x5 props? Thanks

neca79

297 points

I recommend for this engine 7.2v ~ 11.1v (2s ~ 3s) 800-1000mAh. Confirm the message

FooFilighter

38 points

xcopter 1000mAh ? *) 9x5 props ? (haha) i think you can use more than 2000mAh but remember it must be 25-50C ( 3S turnigy nanotech ) or more :> if i help give me credit :>

BEST ANSWER CREDIT AWARDED

Jonathan

87 points

I use 3S with 6x4 or 7x5 prop. For this prop, You should use battery 2S.

AirHoon

18 points - 2/25/2012

Hi. Does anyone know if this motor will work ok on the newish Hobby King Reaktor 3D, using an 8x4 or 8x6 prop? The recommended motor is out of stock. Thanks.

smartguy

268 points

This motor is a little more powerful than recommended for that plane, but it shoud work just fine
If you like my information let get me rewarded :)

Martins

1 points - 2/14/2012

Can i use a 4s battery on this ?

smartguy

268 points

No, you have to use a 2-3s bettery 4s will burn the engine
If you like my information let get me rearded

BEST ANSWER CREDIT AWARDED

Joao

2 points

ok, thack you a lot smartguy for your awnser

Joao

2 points

becouse i had the same question on my mint

auto5

95 points - 2/9/2012

How much thrust will i get out from this with a prop 6x4e or 6x5e?

smartguy

268 points

570g on both props (570g at full speed) sorry for my english if you loke my information let get me rewarded

CHAMBO88

89 points - 2/4/2012

what prop should i use on a 3s battery?

smartguy

268 points

hi chambo88 sorry for my english you can use 7x5 9x5 10x5 i recomend 9x5 Iff you like my information let get me rewarded good flights

Jonathan

87 points

I have this motor and I'm using 6x4 and 7x3 prop. For prop 8x4, I use 2s battery.

Schletzer

49 points - 11/25/2011

Hello
How much is the diameter of the outer holes of the cross?
Thanks Juerg

David

22 points

Hi, the center of each hole to the opposite of the other side is 1 5/16. point to point is 1 15/16. sorry for inches I don't have anything to measure metric

Uberfest

31 points

muito bom, recomendo

Yuto Kang

11 points

It's 34 mm for the mounting holes on the X, center to center. I purchased their digital caliper a while back and I love it.

pipercub

65 points - 7/18/2011

i cannot get this motor to work with the hobbyking ss 25-30 esc, does anyone else have this problem or can help me with it please?

Toad1

49 points

I have this motor with the same esc, and it works great, so the combination shouldn't be the problem... What kind of problem is it, does the esc do anything, beeps when you connect it to the battery?

BEST ANSWER CREDIT AWARDED

pipercub

65 points

Ahaha thanks i figured it out, it was a wiring problem on my part, i spliced the wires but forgot that they were covered individually, just sanded it down and respliced. Thanks anyway!

Uberfest

31 points

otimo, recomendo

Herick

1 points - 5/4/2011

Propreller recomended?

rcdude11

25 points

8x4.3 is good on 3s

giuseppe

9 points

9x3.8 oppure 9x4.7

cshardware

76 points

Best Prop Size 8050 on 3S

eliana

266 points - 2/21/2011

Cuanto es el empuje en gramos de este motor ?

__CT4

6 points

The g at the end of the 620 is a bit of a givaway

Customer Reviews

Overall Rating		pete23 30 likes
Value
Quality

Like it?

Hum, don't know why the other guy has had problems with his, but mine is built like a rock! I got sand in it, slammed it into the asphalt, scratched it up, and it still works great. Here are some specs, TURNIGY nano-tech 1300mah 3S 25~50C Lipo Pack TURNIGY Plush 25amp Speed Controller TURNIGY L2206A-1650 Brushless Motor (130w) 7/6 prop 18.22 - 19.23 amps 205 - 223.6 watts This pushes my 36" epp wing like a rocket, straight up into the sky! Insane performance.

7 comments. Reply..

Overall Rating		dvddcsy 19 likes
Value
Quality

Like it?

I adjusted the shaft position in the rotor to reduce the end play because the bearings felt rough. After a brief run the bearings felt smooth. After 1 hour of flight time the bearing still are good. I am using a 3S 1000mAh LiPo with a 20 Amp ESC and a 7X6 prop in a 1 meter, 500 gram pusher wing. I get 12000 RPM, 17.5 amp and 200 Watt static but about 7Amp average in flight. Motor is barely warm. Good speed and unlimited vertical climb. The Kv measured about 1705. The resistance measured 41 mOhm. A larger diameter lower pitch prop might be more efficient if you have room for it. I like it.

No comments. Reply..

Create an account

Overall Rating		Nissan Convert 14 likes
Value
Quality

Like it?

Good accessories & appears well made but the bearings let it down. They are very rough & because they are sealed you cannot clean & regrease.Hopefully I can find some to replace them.

No comments. Reply..

Create an account

Overall Rating		Not I 5 likes
Value
Quality

Like it?

Good solid motor, has worked for 2.5 hours without any problems. Works well in my small 3d park flier. Turns a 9x5 with ease, included hardware is nice, and looks good. Would recommend to a friend, and would buy again if i needed a replacement.

1 comment. Reply..

Create an account

Overall Rating		devine 10 likes
Value
Quality

Like it?

very good, you can safely recommend.

No comments. Reply..

.....click here to see all reviews