USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
More than just a fancy name. TURNIGY nano-tech lithium polymer batteries are built with an LiCo nano-technology substrate complex greatly improving power transfer making the oxidation/reduction reaction more efficient, this helps electrons pass more freely from anode to cathode with less internal impedance. In short; less voltage sag and a higher discharge rate than a similar density lithium polymer (non nano-tech) battery. For those that love graphs, it means a straighter, longer curve. For pilots it spells stronger throttle punches and unreal straight-up performance. Excellent news for 3D pilots! Unfortunately with other big brands; numbers, ratings and graphs can be fudged. Rest assured, TURNIGY nano-techs are the real deal, delivering unparalleled performance! Spec.Capacity: 4000mAhVoltage: 2S1P / 2S Cell / 7.4VDischarge: 35C Constant / 70C BurstWeight: 234g (including wire, plug & case)Dimensions: 152x49x14mmBalance Plug: JST-XHDischarge Plug: 4mm Bullet-connector The nano-core technology in lithium ion batteries is the application of nanometer conductive additives. 1) The nanometer conductive additives form ultrastrong electron-conducting networks in the electrodes which can increase electronic conductivity. 2) These additives create a superstrong ability for imbibition in the carrier liquid to supply more ion channels. This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly. Advantages over traditional Lipo batteries:-Power density reaches 7.5 kw/kg.-Less Voltage sag during high rate discharge, giving more power under load.-Internal impedance can reach as low as 1.2mΩ compared to that of 3mΩ of a standard Lipoly.-Greater thermal control, pack usually doesnt exceed 60degC-Thickness swelling during heavy load doesnt exceed 5%, compared to 15% of a normal Lipoly during heavy load.-Higher capacity during heavy discharge. More than 90% at 100% C rate.-Fast charge capable, up to 15C on some batteries.-Longer Cycle Life, almost double that of standard lipoly technology.
PRODUCT ID: N4000.2S.35
I am new to electrics, so if this is a novice type question I apologize.
I received two of these batteries today. I am charging the first now. I have a HobbyKing ECO-6 charger and I've set it for LiPo 3S Balance 4A 11.1V. The most current the battery took from the charger was 2.1A. Why? I've set the charger for 4A and the battery is somewhat discharged (cells were about 3.5V measured using the LogView application (I've connected my ECO-6 to my PC so I can monitor battery charge performance).
Someone asked the question on measurements:
153mm length
48mm height
22mm width
53mm height at wire exit from battery
115mm Power lead length to connector
34mm Power connector length
55mm balance connector length
332 grams
hi, i have a wot4 foamy. NOW the thing is its recomeded i use 3s 2200 mah,just wondered if these will work ok in it?
40a asc 12x7 prop 950kv motor all stock. Thanks
Wow, great battery, great price and very nice finish. similar battery is about six times the price yes hobbyking charges a bit for over weighting it but still much cheaper.
boought 2 of theese to make a 16s pack together with 2x6s, 3 of the cells were good, one is slightly higher reading on Ir even after 5 test cycles to 5pcnt around 3.5-4 mohm which is too high, will have to buy another pack to get another cell, ohh well, quite cheap so its not that bad. the watthour vs gram and amp vs gram on this cell is very good
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg){kind=small}
