Spur Gear 82T - A2030 and A2031

 jeffrey 669 points

I do not know if the Losi spurs work,but I do know HPI spurs work,That is what I have replaced mine with,5mm center hole 48 pitch.Got mine at local hobby shop for $3 bucks.As long as center hole is 5mm ,they will work.85 tooth is the largest size,so you can still use dust cover.I used a 87 tooth but could not use dust cover.Hope this helps.JK.

 crashd 103 points

thanks, and the hpi works with the slipper disc?

 Josh 2 points

Will this spur gear www.link

 jeffrey 669 points

The HPI spur gears work,you can modify the slipper clutch discs to work,or just get HPI slipper clutch discs.JK.

 jeffrey 669 points

5mm and HPI spur gears also work that you can get at local hobby shop.

 jeffrey 669 points

Yes you need a few.Also Hpi spur gears work and you can get them at a local hobby shop.Hope this helps.JK.

 Remko 529 points

It did not help... I already had them on my shelf. :)

 jeffrey 669 points

Hpi spur gears work also,$4 at local hobby shop.87 tooth.Hope this helps.JK.

 Ebiker 160 points

My new Kyosho spur starting to go bad after one pack too. I think the problem could be actually the clutch spring. It too stiff. I had to back it off having the nut only on two threads to get some slip from the clutch.

 jeffrey 669 points

My first one was too tight of clearence. 2nd one I put more clearence between gears and is still going strong with clutch spring tight.

 jeffrey 669 points

Its a 48 pitch.Hpi spurs work in the desert buggy.I have a 87 tooth hpi spur in mine.The only thing the cover will not fit with any spur bigger than 83 teeth.Hope this helps.JK

 Mauricio 1 points

thanks for your help

 traxxrc11 346 points

I have never seen a metal spur from hk so i assume No

 Vrdetailing 78 points

Maybe its better to have a weak point..

 thren 62 points

there always needs to be a weakest link in a drive chain. In this drive chain the spur gear is the weakest link, its cheap to replace and protects the more expensive parts. Its a good choice for a part thats easy to replace and dirt cheap, and when it breaks it saves the other more expensive bits....If they made a metal one, you need to think ...."whats the next bit that will break ?"

 Mr Sexy 16 points

If you need a metal spur thers a good chance your doing some thing wrong, if you set the mesh correctly you should have a problem. I've had plastic spurs on all sorts of rc's and they last a fair while when done properly

 Dale. J 1 points

your slipper clutch is not adjusted properly if you are stripping the plastic ones. Try loosening it off a bit and see how it goes. If you put a metal one on you could end up damaging something else worse than a spur gear.

 leclere 19 points

If you break this part,it means that your spur and the pinion gear are not adjusted !!! The best way to avoid issues with this part is to put a piece of paper between the spur and the pinion gear, with this method you have a right space between these parts.

 traxxrc11 346 points

metal is not good option,plastic spur is best,it absorbs the impact

 leclere 19 points

no metal spur gear at the moment ! the motor pinion is in metal, so the plastic spur gear act as a fuse in case of problem.

 traxxrc11 346 points

This may be cheaper,but softer

 thren 62 points

because it is not branded "kyosho"

 Otomar 15 points

it's not very good material

 Dale. J 1 points

your slipper clutch is not adjusted properly if you are stripping the plastic ones. Try loosening it off a bit and see how it goes. If you put a metal one on you could end up damaging something else worse than a spur gear.

 SammyC 80 points

Relatively soft plastic and quite a lot out of round, which requires very careful setting of gear mesh. Also because of tight/loose backlash throughout rotation, pinions won't last as long as in other higher quality setups. But, both the pinion and spur are so cheap, get a heap of them while they are in stock!

 traxxrc11 346 points

Kyosho one is harder nylon,i guess

 Otomar 15 points

Kyosho or Losi is better choice

 jeffrey 669 points

Hpi Spurs work also

 HartmannUA 17 points

i wait 1 month.

 Zeratul 76 points

It was just in stock a couple days ago, you have to put the email alert because some of the popular items come in stock and they sell out fast.

 dantheflyingman 81 points

never?

 Königseder 12 points

yes its stock

 FITZGERALD 4 points

yes there should be stock

 Oscar 13 points

in stock

 grimpeur 79 points

the pitch is 48p, like a lot of 1/10 spur gear

 FITZGERALD 4 points

the pitch is 48p like a lot of 1/10 spur gears

 Königseder 12 points

www.link this picture is from kyosho ultima, i think its the same

 Andrei2J 3 points

also looks the same as HPI e-firestorm and trophy mini.

 omardude 21 points

kyosho ultima DB will fit. make sure you get the 82T

 Steven 9 points

Hole is 5mm in diameter, the width at the outer edge is 5mm and the diameter is 44.3mm

 Jakkie 2 points

Can sumone pleaze give me part number for spur gear