USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
Super small and light weight, the FrSky TFR6M is a perfect choice for park flyers and indoor models. It weighs in at only 3.4 grams!
This micro receiver is compatible with FAAST 2.4G Air Systems (7CH Mode/Multi Mode)
Compatibility: - FAAST 2.4G Air Systems (7CH Mode/Multi Mode)
Features: - Super small and light weight, designed for park flyers and indoor models - Two selectable failsafe setting options - Compatible with FAAST 2.4G Air Systems (7CH Mode/Multi Mode)
*Note: This RX uses micro JST connectors
Specs: Number of Channels: 6 Operating Voltage Range: 3.5~10V Operating Range: >300M Size: 31x23x7mm Weight: 3.4g
Yes, you must used standard connector for Bat/Thro in this www.link example, I haven`t change the connector on ESC, but I had to replace servo connectors with the included in this reciver.
Or you can search adapter for your plug: www.link
You must connect ESC to the last connector, and battery connect to ESC(as motor) *-)
I used Futaba 6EX and this config with Micro Liadon plane, and work fine.
I have connected only 1 servo cable between TFR6M (ch3) and KK2.0 (Yaw). Is this correct ?
KK2 is in cppm mode
T8FG is in 7ch mode
But i can't arm or use self level switch
Any idea ?
Oi Ariana. Segundo as especificaç*õ*es, ele binda com qualquer futaba FASST, mas preste atenç*ã*o, pois os conectores para servos sã*o diferentes do conector para ESC. De repente isso pode ser um problema...
lembre-se de conceder credito de "melhor resposta". boa sorte
BE CAREFULL!! 1S operation requires secure operation under 3.5V So trouble may occur when you need it: Difficult situation* throttle up* voltage drop* connection lost* disappointment all over the flour
is there anyway you can set this up for 1s flight?3.7v? i could only run 50 mah out of my 250mah batt ,i have f/s off in the transmitter but dont know how it works with reciever with low voltage?any ideas?
HI there I was try again new receiver then fund out i am oh blind oop my radio trade 7ch will be work connect to receiver the light come green good work thank you company hobbies king.
HI there any one can who help to me?
Myradio futaba 8TG super try connect new receive the light red and green still light light light put point hold on receive bind light No naswer try come green notwork i not understand why but i did before read maunalfor TFR6M ?
Have you 1) pressed the FS/bind button and 2) THEN powered on the TFRM6? Dont bind Futaba style, pressing link after receiver power on. (also check your 8FG is in 7CH or Multi mode as the product description says nothing about MLT2* havent tried this Rx yet)
I understand I'm not the only one then, that could not use the 'recommended' connectors (Ar6300) as they are too beefy for this RX.
I am thinking of soldering wire leads directly to the RX. I've had enough.
since it has too tiny connector it is difficult to solder it. i have tried to solder it and make "standard" servo connector, but it ended with not working receiver. eventough it was successfully binded with my futaba 6ex before.just use recommended connector as its designed.
Hi again... OK, I have received the [MOL125F-LEAD] wires - lo and behold, the FIT :)
So, if you're buying this receiver make sure you get these and NOT the [Ar6300 Mini JST Plug and Servo Lead]
Is this compatible with the Walkera WK-2403 2.4 G spread spectrum transmitter , and if not , which HK micro receiver is compatible with the Walkera TX ?
Are they difficult to bind using the bind plug ?
Which plug do you use to connect the receiver battery ?
Is there an ESC built in , or do you have to use an external ESC ?
I have ordered this bag of connectors: 1x #JSTMF-2S-20/9735 JST-XH 2S Wire Extension 20cm (10pcs/bag) = $2.71 and they are too bif for this receiver. Which connector exactly is for this receiver and where can I but it? Thx.
You can also get 2 of PRODUCT ID: MOL125F-LEAD and 1 of PRODUCT ID: AM-1021Bx10. With a little soldering work, you will have 10 of appropriate connector :)
It was a software load issue. I loaded the latest Firmware on the Multicopter board and it works now.
Customer Reviews
Overall Rating
GustPilot
259 likes
Value
Quality
Like it?
Nice little product for such a gr8 price and weighs only 3.4 gms, with the outer cover gone can weigh much lesser, (I am going to keep it on for a while though). Range is more than 300 mtrs, no issues on that. antenne diversity aint there, for 300 mtrs (Beyond that you wont see the model of micro size, i guess) one antenna is good enough. great product HK, Thanks
No comments. Reply..
Overall Rating
FLY1ON
293 likes
Value
Quality
Like it?
The only complaint is the channel numbering, which at first fooled MY old eyes..... 1 2 4 5 6 3 and Channel 3 is regular pins not micro molex, so if you're like me slow down and look closely, due to esc Turnigy 6a having micro molex, i just slaved CH4 to CH3 and bobs my uncle! ha ha ha. bind was so fast and works awesome, plane is too small for me to worry about range past 300 feet... Cheers
Ultra small receiver binds easily with 8FGS. All channels work perfectly. weight without paper cover is 2.95g! Can use built in programmable failsafe or Tx defined failsafe.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg){kind=small}
