Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Hardware & Accessories > Wires & Plugs > Battery/ESC/Motor Connectors
> Hardware & Accessories > Night Flying Accs.
> Chargers & Accessories > Balance Leads
> Chargers & Accessories > Battery Adapters

  RATED:

JST-XH to JST LED Power Distribution Lead (4 JST)

JST-XH to JST LED Power Distribution Lead (4 JST)

JST-XH to JST LED Power Distribution Lead - A neat way to power LED's from 3s Lipoly's using the balance plug.



** WARNING: Check Polarity of your setup before connecting this harness.



PRODUCT ID: 258000016

This product available from a warehouse near you!


Weight: 25g Quantity: 
International Warehouse
stock
10+
USA West Warehouse In Stock View Item
Price $0.99

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
529
crowns
  
 
Total of 17 discussions.
dangerdan  9 points - 2/17/2014
 
I'm having the same issue. I want one for 2s and I can't find one. Kaushal - If you can use this for 4s kindly explain how. This is a 3s adapter
 canterburyflyer 321 points
Solder on from perf board and copper tape or copper wire and header pins. All should eventually be in your kit sooner or later
harminder  1 points - 1/21/2014
 
I am running my x900 on a 4 cell and sometimes a 6 cell. All of the options here seem to be for 3 cell. I cant see a product or a mod. Any ideas?
 Kaushal(India) 55 points
You acn use it with a 4S no problem.
 canterburyflyer 321 points
Yeah? And how are you going to get the balance plug into that male DF13 header block. It only allows for 4 pins so it won't let you squeeze another in there!
Oscar  2 points - 12/10/2013
 
Can i use this to power up my gimbal? Thanks
 Kaushal(India) 55 points
Yes, you can
kydave  6 points - 9/3/2013
 
The picture that is above is correct but I'm telling you mine was wrong. If the one I received was correct then all the other JST connectors I have are wrong. On the KK 2 LCD you can add a pigtail so you can see battery voltage on screen and it was wired right because I used it before without smoke. I can't believe that all the other JST connectors on batteries and sets I have gotten from HK are wrong and this one is correct besides I now see a WARNING: Check Polarity of your setup before connecting this harness so they must had some get by wrong.
kydave  6 points - 9/2/2013
 
I have one of these and the red JST ends are not correctly wired and it caused my KK board to smoke. BEWARE!!!!!!
 the right stuff 1682 points
The JST plugs are wired correctly. What were you doing with it to fry your KK board. There should only be one BEC input on your KK board. It does not require any additional power... This is designed for lights and should be a direct connection to the LED'S and your battery via the balance lead. It should not be connected to the flight board!
Customer Reviews
Overall Rating
slyhq
220 likes
Value
Quality
Like it?
BE WARNED!!! JST polarity comes opposite to what it should be! Don't assume every connection factory-made are correct. Killed a couple of strips of LEDs with this distribution lead :( ( thus low in quality ) Other than the wrong polarity, it is a handy cable to supply power to LEDs or other application. ( thus not bad on value )


4 comments. Reply..

Create an account
Overall Rating
faerietree
13 likes
Value
Quality
Like it?
nice if you need a tidied up power distribution for several individual leds or sets - although i prefer the multi remote switch www.link for the blinker of me and my little sibling's truck.
What i am thinking of using this for is for a power supply switch which switches between batteries (controlled by a micro processor). but i'm not sure yet, if it all works as expected. Shall be some kind of redundancy for a critical Quadcopter Application.


No comments. Reply..

Create an account
Overall Rating
RCBUG80
141 likes
Value
Quality
Like it?
great for powering multiple leds from you 3s balance plug


No comments. Reply..

Create an account
Overall Rating
Gadget-Geek
111 likes
Value
Quality
Like it?
These are great!. I hated soldering JST wires to my power cables, Now I don't have to. If you want to use them on bigger or smaller batteries just get the corresponding balance connector and solder it on in place of the one that it comes with. Just remember not to reverse polarity when replacing connector and these only tap off one cell so your LED's may not be as bright as if you hooked them up to your power cable.


1 comment. Reply..

Overall Rating
Jimmy
16 likes
Value
Quality
Like it?
WARNING! These connectors are wired wrong. I ordered 3 of these and all of the 4 JST connectors were wired in reverse polarity. I wasn't paying enough attention when testing a LED strip controller and burned up the wires on my 40amp ESC. You can correct this by using a paper clip or something very small and push down on the tiny metal tab on the pin in the JST connector and pulling on the wire and the pin will pull out of the connector. Make sure to bend the tab back up before you put it back in the correct position in the connector as this is what locks it in the connector.


3 comments. Reply..

.....click here to see all reviews
Aff. Link