USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Multi-Rotors & Parts > Flight Controller

  RATED:

Hobbyking KK2.0 Multi-rotor LCD Flight Control Board (AU Warehouse)

Hobbyking KK2.0 Multi-rotor LCD Flight Control Board (AU Warehouse)
Hobbyking KK2.0 Multi-rotor LCD Flight Control Board (AU Warehouse)

Designed by the Grand father of the KK revolution, Rolf R Bakke, exclusively for HobbyKing, the KK2.0 is the evolution of the first generation KK flight control boards. The KK2.0 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed. simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and your ready to go! all of which is done with easy to follow on screen prompts!

The original KK gyro system has been updated to an incredibly sensitive dual chip 3 Axis gyro and single chip 3 axis accelerometer system making this the most stable KK board ever and allowing for the addition of an Auto-level function. At the heart of the KK2.0 is an Atmel Mega324PA 8-bit AVR RISC-based microcontroller with 32k of memory. An additional 2 motor output channels have been added to the KK2.0 allowing for a total of 8 motors to be controlled (Octocopter). A handy Piezo buzzer is also included with the board for audio warning when activating and deactivating the board.

If your new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.0 was built for you. The 6 Pin USBasp AVR Programming interface ensures future software updates will be quick and easy.

Specs.
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram (Inc Piezo buzzer)
IC: Atmega324 PA
Gyro: InvenSense Inc.
Accelerometer: Anologue Devices Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
Firmware Version: 1.2

Here are some How-to Vids:

Part 1

Part 2

Part 3

Part 4

Part 5

Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Aero 1S Aileron
Aero 2S Aileron
Flying Wing
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option)

The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.


Whats is a Multi-Rotor Control board you ask?


The HobbyKing KK2.0 Multi-Rotor controller is a flight control board for multi-rotor Aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega324PA IC. The Atmega324PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.

The HobbyKing KK2.0 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega324PA IC via the ail, ele, thr and rud inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).

Note: A user manual is available under the files tab.
*Royalties paid on each unit sold to Rolf R Bakke, the original KK Designer.


PRODUCT ID: 9171000073

This product available from a warehouse near you!


This is an archived page. This product is no longer available and has been replaced by a newer product.
CLICK HERE TO VIEW THE NEW PRODUCT


Weight: 55g Quantity: 
United States Warehouse Out Of Stock
stock
BK
Price$30.99


Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
STOCK ARRIVAL ALERT

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;
 Customer rated
511
crowns
  
 
Total of 59 discussions.
Succar  655 points - 4/1/2014
 
http://www.youtube.com/watch?v=A8Ub9lzvwbU
 RonRC 3238 points
Here is how well this board can fly even with the firmware that it arrives with. This quad was made and flown before any firmware was available.
 RonRC 3238 points
But, with v1.5, it flies my UFO around with great stability.
Rodolfo Carlos  3 points - 3/23/2014
 
Hello. I have a problem. My battery has 12 08 Volts and KK2 said to have 6.7. The gyros and the acc indicate not ok
Jason  1 points - 3/20/2014
 
Hi, I'm wanting to update my KK2.0 but the flash tool doesn't offer me this board in the controller options... Any ideas?
 Succar 655 points
jason take a look in my blog rcnaveia com br theres a print screen in the multicopters session in the Stabilized Gimbal using KK2.0 post
richiewato  3 points - 3/4/2014
 
this is a great little board. Here is it in action on a homemade Tcopter (tricopter) and 2 axis gimbal with Hero3
 RonRC 3238 points
richiewato, Awesome video! You put some great shots in there. Brushless gimbal??
 richiewato 3 points
yep - thanks www.link
richiewato  3 points - 3/4/2014
 
this is a great little board. Here is it in action on a homemade Tcopter (tricopter) and 2 axis gimbal with Hero3 http://www.youtube.com/watch?v=aP-DTVWpNYg
Customer Reviews
Overall Rating
CH33ZEBURG3R
4 likes
Value
Quality
Like it?
Super FC board, works really well and is very easy to use, especially when out and about, the firmware is simple to update but you will need the cable which is not supplied. It can only get better and for the price it's perfect.


No comments. Reply..

Overall Rating
CH33ZEBURG3R
4 likes
Value
Quality
Like it?
Well i found a buddy code on rc international which made this $19, it's just a shame that we have to pay $8.99 minimum for postage,(unless you can pick it up from instore) which brought it in line with the International price, but anyway mine had arrive within 24hrs, so can't complain. Anyway it's a great board and very easy to use, this is my second one now for my new quad i'm going to build and i'd highly recommend them.


No comments. Reply..

Create an account
Overall Rating
thumbglitch
49 likes
Value
Quality
Like it?
The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.



No comments. Reply..

Create an account
Overall Rating
PageDM
35 likes
Value
Quality
Like it?
Great little board, some of the connectors and LCD were soldered on a little crooked, most people may not be bothered but an easy fix with the soldering iron. Awesome value for money, makes building a multi very easy for newbies such as myself


No comments. Reply..

Create an account
Overall Rating
Docspace
206 likes
Value
Quality
Like it?
What a stand out product, very cheap ,but delivers the goods that's required for all you quad copter needs, really simple devise to use, buy em you wont be disappoint 5/5


No comments. Reply..

.....click here to see all reviews
Aff. Link