USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
High performanceMETAL GEAR micro servo for use in glider/EP Planes or car models.
Item No: SSV-9314MG Weight: 14.7 grams / 0.46oz Dimensions: 23 x 12 x 22.5 mm / 0.92 x 0.47 x 0.87 inch Input Voltage 3.6V ~ 6.0V Torque At 4.8V: 1.5kg/cm , 21 oz/in Torque At 6.0V: 1.9kg/cm , 25 oz/in Speed At 4.8V: 0.13sec / 60 deg at no load Speed At 4.8V: 0.12sec / 60 deg at no load Running Current: 185mA Stall Current: 410mA Horn Gear Spline: 25 Segments Connector Wire Length: 160mm (6.29in) Connector Housing: Futaba connector Ball Bearing: One ball bearing on the top Gear Type: Metal Gear
I use Twice of them onto a F27B Striker with powerful engine since almost 2 years without problems, a really pleasant servo for a minimum quality/price ratio and a maximum pleasure
I have the original HXT version of this servo. They do not look anything like what is pictured. Searching the web, it looks like these servos are now made by a different factory and the quality has dropped. It is a shame that the reviews for the old product have been attached to something that is reported as being significantly inferior.
Picture incorrect. Mounting taps differ. Similar to corona ds929/939. Not the best for mounting on a 450pro heli. Servo horns weren't design for helies,very small and bendy . All the glowing reviews,but mine stripped after auto land,gust of wind tipped it to its side (grass surface).
Customer Reviews
Overall Rating
DominikM
likes
Value
UNRATED
Quality
UNRATED
28 thumbs up!
For the last 6 months, I have have been using 3 of these servos for collective control on my Trex 450. Over that time I have had numerous bad crashes and the metal gears have not stripped once.
Performance wise, the speed of these servos is probably on par with traditional Trex servos, like the HS65s and HS56s, but they don't have quite the same smooth feel. Centering accuracy and power are more than sufficient for a Trex-450.
They do draw a considerable amount of current. Three of these servos, combined with a receiver, gyro and small digital tail servo, manage to overload the 2Amp BEC on my speed controller (The ESC overheats after about 5 minutes of hard sports flying and light 3D).
The supplied horns are brittle, so be careful when trimming them.
No comments. Reply..
Overall Rating
Bruce Simpson
likes
Value
UNRATED
Quality
UNRATED
15 thumbs up!
These servos appear to have the same motors and feedback pots as the Hitec HS81 and have proven to provide excellent torque. I'm using then in a slow-flying SuperTigre-90 powered UAV with no problems and on the elevator of my 52-powered Bobcat pusher-jet. Only one failure so far but that was after more abuse than an HS81 could ever take.
No comments. Reply..
Overall Rating
John Gibbs
likes
Value
UNRATED
Quality
UNRATED
13 thumbs up!
This servo has just been fitted to a small slope glider with a Spektrum 2.4Ghz radio system, it is very fast and precise - a high quality servo, it's shallow depth would make it suitable for wing mounting and is supplied with full size output arms.
No comments. Reply..
Overall Rating
celle jean-philippe
likes
Value
UNRATED
Quality
UNRATED
12 thumbs up!
excellent!
Very high torque!
Good precision
mount on my cap 232 .25 hobbycity
Thanks Hobbycity!
J-P
No comments. Reply..
Overall Rating
Oliver Jergis
likes
Value
UNRATED
Quality
UNRATED
12 thumbs up!
T-Rex 450 v2 mit 3 HXT 9314 MG an der Taumelscheibe und einer am Heck :-)
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg)
