Nylon Snap-Click style clevis 2x8x23mm (10pc)

 macchp 119 points

I just uploaded a couple of picture under the tab "files". They will be available as soon HK will release them. The clip in the picture is smaller than this, but it works exactly the same. Are used to avoid an "L" bend rod can slide off the horn. It's easier to "L" bend than "Z" bend and the clip will secure it as good or even better than a "Z" bend rod.

 Drugos 1975 points

Yes,it is.

 Johnny 6 points

100% fine and safe

 Sally 659 points

Yes very very good BUT no adjustment. So it is good for only one end of you push rod. I do not know why we do no see more of these used. Some times it is so hard to get a Z bend into a glued horn?? Thanks

 munsaf 291 points

jay toadyon kuoll ak moon alaa paichkus hagaun ty v naly tusiun muon khula da 3mm

 Patrick 7 points

sorry i speak french or english only!

 igor 35 points

It is for wire 2mm.

 Sally 659 points

Hay I find bike spokes fit very well

 munsaf 291 points

ahoo jee uton da hadd kr diti si anyy v samjung da snap clik daa moon chorion garamun kr ky khul krna pao..

 crashnfoam 29 points

2mm is .078 music wire used for larger models

 Drugos 1975 points

.078 music wire.

 Sally 659 points

So if 1 cm = 0.3937 then 1 mm = 0.03937 I must agree 2mm = 0.0797 inch. wE HOPE WE HAVE HELPED

 Heppy Ket 380 points

ebr62933(AT)bigpond****.au

 CHAMBO88 89 points

is that a . net or . com?

 CARVER99 17 points

you should post in the forum under buddy codes

 Sally 659 points

So we are at the 29Nov12. The buddy code must have expired NOW. Thanks anyway.

 robin3dbug 108 points

any rod that is 2mm fits it

 Aleksandr 6 points

any metallic rod of 2 mm recurvate under of 90 degrees

 Egor 8 points

any metallic rod of 2 mm recurvate under of 90 degrees

 thyDusk 18 points

2x8x23mm

 CARSLOS ANDRE 58 points

The hole is 2mm diameter is 8mm length is 23mm

 vmail 8 points

2x8x23. The distance from the hole and the back end is 20 mm.

 kapeti2108 16 points

Hallo Thomas,
du kannst es kaufen... :-) War nur ein Scherz. Wenn deine Schubstange aus 2mm Stahldraht ist, musst du die Ende in 90° abbiegen, so im loch vom Steuerhebel stecken, und dann mit dieses "clips" kann man es sichern, dass es nicht mehr rausrutscht. Hoffe dass ich helfen konnte.
Grüße aus Ungarn...

 Eagle 340 points

Besten Dank für den Tipp...nun habe ich eine Vorstellung davon...ist ja genial!
Viele Grüße zurück!

 sampc69 950 points

i could not understand..!! why you did not answer in english? :(

 Battle fury 97 points

this is use to fully secure servo control rod to prevent from any freeplay with servo horn and rod

 Mate 19 points

You can connect the round end of this clevis to the push-rod,and you can connect the thin end to the servo arm for better stability and less push-rod bends.

 CARSLOS ANDRE 58 points

Used to catch their lincagem very useful for signal

 Sally 659 points

They are great to secure control rod to horns. It means you just have to bend the rod at right angles rather than a dog leg.