USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
This motor is realy wonder. I bought it four years ago and crashed it into water, dirt, mud, concrete... It is still working PERFECT... This is my favourite motor for sure!
I ordered this motor and the hextronic 24gram motor, but I received two "hexTronik 24gram Brushless Outrunner 1300kv"
one was in hextronics box and the other motor was in turnigy box , but the same products
I loved the beauty of this motor than the hextronics s h i t , They have sent me the wrong product , I cant wait anymore , what should I do ?
Yeah, this motor is just another version of the famous BlueWonder, i´ve used this motor as a replacement for my 1300kv bluewonder, 8x4 prop Quad and it worked just fine. This motor will handle a 3s just great. On a 8x4 and a 3S, this will pull about 370g, so 4 of them will pull more than 1kg. On a 9x4.7 it will pull almost 1 pound each. Good luck.
I really wouldnt use these on a 1KG and more heavy Quad as the Thrust Ratio will be to small and under 2/1 get t he 28xx Series E-Maxx instead for 6.05 using a Buddylink, they have moire thrust and are more reliable. If you like this iNfo please let me get credited.. thanks
Yes, the amp draw with the prop range suggested and the battery suggested doesn't exceed 10a so you are pretty safe using a 12amp ESC. You shouldn't use a prop bigger than 9x4.7 with a 3S or you could burn the motor itself. A very popular setup is this motor with a 8x4(or 3.8) prop with either a 2S or 3S. Good luck!
You can use any connectors you like, they all works as well. You could also buy the 24g Hextronik 1300kv motor which is exactly the same, minus the connectors and the shrink-wrap.
what size plane is it on and what type of flying are you doing? it sounds like you are using too much battery, weight wise, I fly mine on a 6 oz foamie and use a 500 MAH 3s Turnigy battery, my flight times are 6-8 mins. I don't think thrust is your problem, weight seems to be a larger issue
Well, I think you are better off with a higher kv because of jets you will be using a smaller prop diameter, typically a 6x4 or a 5x5 so you will need the increased kv. There is a 1700kv version of this motor, I would get that.
It doesn't come with the screws for mounting the motor. You can use the screws that come with servos to mount them on wood planes if you are not screwing them down...
I also waited because it is an engine that is worth is very economical and strong my models is approximately 450g and I use this motor with a Turnigy esc of the 20th and a 3s 1300mAh battery, a battery life of 15 minutes flight. cost-effective.
Great little Motor. I am using it for my 270gm J3 Cub. It is providing more than enough power. I am using both 2S and 3S Lipos. 3S I am using it with 8x4 props while the 2S I am using it with 9x7 props.
I am using two of these with TP Slow Fly propeller 8x3.8 and 2s 800mAh battery. There is thrust ca 250 gr and fly time 20 min in my 300 gr slowflyers.
No comments. Reply..
Overall Rating
Tom Madron
20 likes
Value
UNRATED
Quality
UNRATED
2 thumbs up!
Great little motor. I have two of these.7 to 8 minutes on i8 inch pie planes with 9.4x7 props.They will hover @ half throttle. I will try the 1500kvs next.
No comments. Reply..
Overall Rating
BillW
45 likes
Value
UNRATED
Quality
UNRATED
2 thumbs up!
Great little motor, plenty of 3d power for foamies on 2s/500 packs and 9 x 4.7 apc slo fly props!
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg){kind=small}
