GT-Power Voltage Analyzer 3 in 1 2-6S

Item found in the following categories;
> Batteries & Accessories > Battery Accessories
> Chargers & Accessories > Accessories

RATED:


	GT-Power Voltage Analyzer 3 in 1 2-6S

GT-Power Voltage Analyzer 2-6S

Features:

For the real time display of the R/C model battery voltage and the lowest voltage record and the setup of the low voltage alarm while flying

High precision display of individual cell voltage (1-6S shows separately) and the total voltage

With the special LCD screen which can indicate data clearly

With the reverse polarity protection for cell input

It can setup the range of Lipo/LiFe alarm voltage

Specifications:
Used for 2-6S Lipo/LiFe battery

Volatge display resolution: 0.01V

Dimensions: 69 x 33.4 x 10.7mm

PRODUCT ID: GT-V-ANA

69g

10+

$13.99

Further discounts available for registered & logged-in customers.

Customer rated

579
crowns

Total of 3 discussions.

jimmy

4 points - 2/27/2013

can i set the voltage at which the alarm goes off?

JelleB

478 points - 4/22/2010

Can anybody tell me what kind op microcontroller is in this device? I am looking for a atmega + lcd in a nice case for cheap, but the guesses I made this far have only yielded 8051 type controllers (which need a different programmer).
Can someone post a picture of the insides for me?

iansydbr

73 points - 8/28/2009

Does anybody know if the unit can be calibrated as the one I received has some very serious errors?

AlvaroSpain1971

224 points

I have problems as well, cell 3 displays 0,3 volts down comparing with a Fluke multimeter, other are +- 0,05 in range.

Invertor

20 points

I have the same problem. When I receive it all was ok and measurements were accurate. But in about 2 months of use cell 2 begun to show about 0,1-0,2 volt up. I'll try to solder all resistors on board.

Michal

4 points

cant calibrate, but problem with detection is bcs you need to use jst balance port and not pq. or get adapret from polyquest to jst (turnigy) ballancer port. pq u can use from 4s. bcs on 3s pq ballancer port is "missing" one wire and on 2s are two wires missing. i using this with hyperion 5s and work great. -0,05 volt

Michal

4 points

Customer Reviews

Overall Rating		ostemmen 41 likes
Value	UNRATED
Quality	UNRATED

25 thumbs up!

Think twice before you purchase the GT Power Analyzer. I received mine Dead On Arrival. Blank display. It does not work. Shipping return costs exceed value of device. Why bother with this cheap product. Buy a higher quality power monitor instead! GT Power Analyzer not recommended !

3 comments. Reply..

Overall Rating		Rafael 35 likes
Value	UNRATED
Quality	UNRATED

23 thumbs up!

Comprei p/ usar em uma bateria tipo Life, mas no conseguir usar, alguma dica ?

Bought for use in a battery type Life (2s)s, but i can not use, someone can help me ?

Thnks

No comments. Reply..

Create an account

Overall Rating		Maurivan 56 likes
Value	UNRATED
Quality	UNRATED

21 thumbs up!

O LCD pequeno, poderia ser maior para melhor visualizacao. S testei com LIPO 3S (4 baterias), mas reparei que a celula 3 sempre indicava mais alta a voltagem que as outras celulas, mesmo que o carregador indicasse ao contrario

3 comments. Reply..

Overall Rating		sabeshkin 52 likes
Value	UNRATED
Quality	UNRATED

7 thumbs up!

, 3.4V ,
, 0.3V, . 3-.

No comments. Reply..

Overall Rating		sabeshkin 52 likes
Value	UNRATED
Quality	UNRATED

7 thumbs up!

, 3.4V ,
, 0.3V, . 3-

No comments. Reply..

.....click here to see all reviews