USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
Dimension: 30mm x 12mm, 38mm(with shaft) Weight: 14.5g (kv4500) (not including connectors) Diameter of shaft: 1.48mm Length of front shaft: 8mm Lamination thickness: .2mm
Spec. Battery: 2 Cell 2S/7.4V
RPM: 4500kv
Max current: 6A
No load current: 7.4V/0.4A
Current capacity: 6A/15sec
Internal resistance: 0.473ohm
Dimensions: 12x30mm
Pull: 9400 Prop: EP4040
ESC: 7A Max Current: 6.4A Battery Type: 2S Only Suited for Mini EDF or micro parkjets.
Hi,
i'd like to combine this motor with,
HobbyKing Brushless Car ESC 10A w/ Reverse
Turnigy TG9e 9g / 1.5kg / 0.10sec Eco Micro Servo
for my 1:32 Drift RC Car.
Can anyone suggest me for the lipo battere?
I want to keep as low weigh as i can, maybe for 5 till 7 minutes running.
Screw for mount is M1.4, you can find in HK but beware the length of screw, motor tickness only 2-2.5mm http://www.hobbyking.com/hobbyking/store/ __12073__gaui_100_200_mechine_screws_silver_m1_4x5_x 20pcs.html http://www.hobbyking.com/hobbyking/sto re/__12089__Gaui_100_200_Mechine_Screws_Silver_M1_4x 6_x20pcs.html http://www.hobbyking.com/hobbyking/ store/__11824__Gaui_100_200_Size_Mechine_Screws_Blac k_M1_4x5_20pcs_831805_.html
After waiting 2 months, the motor arrived ... but the axis of 1.5 mm and 2 mm as in this config table of the product. I bought the pinion 2mm and was great. For those who complain now?
it seems as if the 15-20 day wait is a bit longer than anticipated, been waiting over a month for these bad-boys.....I need them, I want them .I gotta fly!!!!!
Yes indeed it was a direct swap for my Xtra 300.
used a 6A ESC and works great I swapped out all the Nine eagles Electronics and used the orange recever and 2.5gm servo's
I'm using a GWS 4x2.5 and a GWS 4.5x3 I found that the GWS 5x3 caused cogging on start up so i'm guessing that its a bit heavy for the motor but it does still work. also using a 1.5mm to 4mm prop saver to stop the props snapping when I land (with out wheels) have fun
any of yous know the diffrece between the high roller and the micro t i would like to know which one i should get
PLEASE REPLY IF YOU KNOW WHICH IS BETTER
micro high roller is cooler IMHO, but it has a higher CoG. hop ups for micro-t mostly fit the high roller too. only the chassis is different basically. sadly the highrollers are out of production now
yes it will slow it down, but I will suggest getting perhaps a 2S lifepo they have them here, they have the same battery life and durability, but slightly less voltage. if not, a 1S will be fine.
Why dont you program your transmitter or ESC to limit the speed. Thats what I did, and I let my buddy's 3 year old play with it, and he was able to control it easily. (TrackStar 18a has 50%, 75%, and 100% settings) HK 310 3ch 2.4ghz transmitter has the ability to adjust top speed from 0 - 100%)
Try to spray WD40 in it... or when you want to open it. Slightly hammer the axle a litle bit on a hard surface, so the rear part of the motor comes loose.
Will this motor survive a 3s lipo. Heatsinks will be used on 'em on GWS EDF50 fans...
Worried that 2s will be barely more powerful than the little stock GWS brushed motors...
It should be fine on 3s, as long as you don't let it free spin. I'm using one on a little Losi Rally car, and I can get through a 500mAh 3s pack without overheating or exploding.
Here is a link to where you can purchase them right here from Hobby King. The Thickness of the motor plate is 2.5 mm. depending on what you are mounting it to. (EDF, or conversion to a pusher) you may want it to be a little longer. I hope this helps. www.link
that setup, TTS-18A and 2s lipo, works great with this motor. As always it will come down to gear ratio. I used it in a 1/24th SCT, and it worked great, with torqu to spare, though I eventually upgraded to the higher kv 1220 10300kv version of this motor, which is highly sensitive to gear ratios.
Dear HK team, it is now about mont and whole my order is waiting for this little motor. Whats wrong? Can You please give use some ETA? 15-20 days is over.
Ordered already 2 of these..I can not find an adaptor to fit the blade on motor. Does anybody knows where I can order impellar hub set which is like GWADP004A but for 1.5 shaft diameter ?
gws3020 V A W T 8.08 1.47 11.88 50 8.01 2.33 18.66 75 7.98 3.19 25.43 100 7.92 4.29 33.95 125 *
gws3030 V A W T 8.01 2.08 16.70 50 7.95 3.19 25.33 75 7.88 4.53 35.74 100 7.85 5.02 39.44 105 *
*=full throttle value
1 comment. Reply..
Overall Rating
mwingo13
31 likes
Value
UNRATED
Quality
UNRATED
8 thumbs up!
Super little motor if fitted with a heat sink ( GWS ) 2 s with 3x3 GWS 4.7 amps with a Plush 6 2 s with 3x2 GWS 3.1 amps Great for a MPX Fox conversion as a pusher
No comments. Reply..
Overall Rating
Big Steve H
176 likes
Value
UNRATED
Quality
UNRATED
5 thumbs up!
These little motors fit PERFECTLY in the GWS and guanli A-10, you can use the fan blades and original fan unit! Everything bolts right in, purchased 2 of these and 2 ESC 12 SS, I mounted them in the engine nacels, they stay cool at all times, also run the 2s1p 800 mah turnigy's grerat flight performance and flight times! HIGHLY recommened!!
No comments. Reply..
Overall Rating
jool2metz
629 likes
Value
UNRATED
Quality
UNRATED
4 thumbs up!
moteur parfait pour le mini memesis graupner de 45 cm d envergure avec un controleur tgy 10A et un gws 3x3 2 servos arrow 5g reste plus qu a attendre le stock de lipo 2s 360mA... egalement mont dans un fox merci UH
No comments. Reply..
Overall Rating
transalpin
42 likes
Value
UNRATED
Quality
UNRATED
3 thumbs up!
Good Motor. Use screws M1.4 not too long ( Motor plate is 2.5mm thick). Otherwise u will damage the coil inside (as I did :-( )
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg){kind=small}
