USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
yes you can use 4 servo for 250 heli, 3 for cyclic and 1 for tail ... but you must know the gyro must setting to analog mode gyro, don't use digital mode gyro , you can burn this servo.
Did you use 6v? they only handle 5v without bruning out. i have never had any of these fail, and i have bought more than 18 of them. 2 failed after some time with 6v...
boa noite pessoal , comprei este servo e nao esta funcionando bem no meu tx futaba 7c ... um interfere no outro , tenho um aeromodelo com 4 canais, sendo 3 servos e esc ... se alguem puder me ajudar por favor ! obrigado
Nathan, it is possible?, yes it is... but 6 metal gear servos consumes almost 3 amps (~0.5 amps per servo). It is better if you put a larger bec... like 5 amps it is more safe.
these are way too small for your application my friend. go to servos and parts tab and click on std. servos 31-49g. there you should find a proper size
I purchased these servos and realized they say jr and futaba plugs will these fit into my spectrum reciever if not can I change the plugs or put an adapter on them to fit.
They dont have a tab like the futaba serves so the will fit all receivers just double check the red and black wires are in the same way as your battery or switch wires are
I have been using these with an issue on spectrum and futaba
si son buenos pero es una gastadera de $$$ y mas si te das un porrazo el metal gear sufre mas que los de plastico, para el swash si te serviria pero para la cola te recomiendo uno mas grande, preferiblemente digital y que sea rapido
not at all. i use the dt750 too. the only problem with this mechanism is that you loose the servo in almost every crash. but it works fine, cant complain.
I think you will have to buy another servo that comes with the right screw to be on the safe side. Using different screws that you have lying around can damage the servo, especially if they are too long and go through too far.
great servos, I have about 25 of them I think. Peel off the stickers on the sides, rough up the sides with sandpaper and glue them straight to the foam on your foam jet, etc. I have them in a Panther edf, F16 edf, Squall edf, you get the picture.
These A5030 servos is what they say to put in this kit
Super Cub 25e ARF by E-flite
I was just wanting to find some that were cheaper
Could someone tell me what would work that is cheaper
Thanks
Not sure why you would want to replace these servos for the others as your not saying what it's going to be used with,as in what plane or Heli,i've been using these Turnigy MG servos in my planes and Heli's with great results,IMO they are just as good as some of the other big name ones but at a fraction of the price,they do show the dimensions of the servo in the description if thats what your looking for. :-)
how do you mount these on your plane?
it would be nice if i could use the same servos on another plane instead of buying new ones because the old ones are glued to the plane
I allways wrap the case with shrink tube and then glue it with PU foam glue. If You want to change it You just go and cut off the shrinktube. The servos won't be spoiled.
Hi, I have found that I wrap the servo with a good grade masking tape and then epoxy it into the plane. If you need to remove it, all you have to do is cut the tape. This way you don't have to ruin the servo with epoxy....Al
Cheap metal servo, but it seem not precise. I can not setup the neutral position for my HK 450 blade pitch.
3 comments. Reply..
Overall Rating
Beserc
99 likes
Value
UNRATED
Quality
UNRATED
38 thumbs up!
If you dont like the smell of burnt carbon brushes, DO NOT USE THEM ON 6V! And look what ive discovered. This servo has the same size gear set with hextronik 900 micros. I placed the gears to my 900s and they are working flawlesly now, more precise, faster and i can use them on 6 volts. The only differance cap part is a little high to accept a bearing, so you have to cahange it too. Believe me, you will like the blue black servos, try it...
5 comments. Reply..
Overall Rating
biggbear
225 likes
Value
UNRATED
Quality
UNRATED
35 thumbs up!
Tried 2 of these servos in an Electrifly EP-Su31, elevator, and rudder, works ok, but.... too much play in the gears. When you move the horn with your fingers, there is a noticeable amount of play in the geartrain. Also, very noisy operation. Good price, appear to be digital, but I wouldn't use them in my heli because of this. Will be changing them out of the aircraft for the HXT 900.
No comments. Reply..
Overall Rating
Shanti
71 likes
Value
UNRATED
Quality
UNRATED
32 thumbs up!
Just got 3 of 'em and shortly tested them. They have on one side a terrible overshoot during fast movements! Be aware of that! The rest seems ok at a short look.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
