Floater-Jet Replacement Motor (AXN-2208-2150)

 Baoxia 2 points

5x5 6x5 high speed props , 20amp is ok as long is you don't go full power the whloe flight

 Ca4lo 141 points

ok i used a master airscrew 6x3 with this on my teksumo. works perfectly

 Baoxia 2 points

7x3 max, you could try it if you want, see if the motor and or esc get hot.

 Michael 41 points

Hi Jason, they are M3x3 grub screws. Thanks for letting me know they fell out. I will loctite my ones in now! Happy flying!

 aaron2233 530 points

hey there this engine i use on my quad and tricopter they can pull a 6 pack of vb beer

 UltraMicro 38 points

Roughly 820grams full throttle.

 wayneuk 294 points

yes perfect combo for it

 Andrej1175 16 points

Yes, you can use this motor with 3s and 6x5 prop. I have used this motor with 7x6 prop on 3s battery and no problem with overheating or someone else...

 javier_david 3 points

yes perfectly, i used it whith 6x5 in may hawk sky with 2200 mah 20c battery and i can fly 20 minutes. it´*s a great motor

 Alessio 50 points

i use 3mm prop adapter and fit perfect

 wayneuk 294 points

if you can fit them on then yes ..also suitable for the mini zephyr flying wing

 Bixler13 33 points

The prop is flexing. Get a stronger prop

 Alessio 50 points

I think it's normal because i use this motor with different prop(now i use a 5x5 apc) and the noise is the same

 Bixler13 33 points

Either the prop isn't balanced or that's just the normal operation. Does it vibrate too?

 Alessio 50 points

no vibration just noise,all the prop are well belanced

 Morten 2 points

Yes! I'm running it with 4S 2200mAh and a 6x4 prop. Runs great and i have no problem with overheating.

 wayneuk 294 points

great little motor

 wayneuk 294 points

i use a 30amp as it pulls over 20amp or did in my test

 wayneuk 294 points

TURNIGY Plush 30amp Speed Controller would be suitable

 wayneuk 294 points

yes i would reccomend this motor also its good

 wayneuk 294 points

jsut keep a eye on the magnets as they can come loose a bit of glue will fix it though so not a problem

 ALCARAFA 305 points

Thanks wayneuk I've read about the problem with this motor.

 wayneuk 294 points

not so much a problem matey ive only had one come loose in over a year & a half ive a few axns & my friends fly axns they have had no issues however at one point i was using mine everyday

 wayneuk 294 points

yes i would of thought so

 Tom 2 points

I have that plane with this motor and 30a esc, 7x3.5 prop and 1300mah battery. It is way to powerful for that flimzy flyes like **** plane. Cavitates like crazy starting at 3/4 throttle. Get a Bonzai or Tek Sumo. Infinitly better flying wings.

 greasmnky 205 points

7x5 prop is too big for this motor, guy above said his is pulling 20 amps [max limit] with a 6x4 prop.

 Alessio 50 points

Thanks greasmnky now i use 5x5 prop with 30 amp esc...but my cambat wings is too fast whit this motor

 William 5 points

Hi, is www.link excelent motor.

 wayneuk 294 points

yes you can use it as is just remove the motor mount from the plane as it will come with a mount also the alloy prop holders are better imho & dont require the bands to hold the prop on

 boim77 32 points

for more safer add the prop adapter 3mm like this product id: GON-D3T6.

 m3tafora 18 points

yah they can be use on tek. Using apc prop im sure they go vertical climb in no time

 Ral fRotten 1200 points

No, 3s maximum, 6x4 prop or 5x5 recomended, max current is 20 amps

 Morten 2 points

I run this motor on 4S. Works fine, lots of power!!

 Marcel 6 points

Had the same problem, fixed it by applying a little ca glue to the magnets, never lost one since

 greengo746 45 points

This motor is a good replacement motor for Clouds Fly. I have put this motor in my park jets, hawk sky and various other diy projects. The long wires are a plus and motor work fine with 6*4 prop. 18A ESC is good enuf.

 Ramron 932 points

I don't see why not.

 n8ander 16 points

Yes, But which cessna 182

 emulldonang 19 points

CESSNA 182 DELUXE,

 n8ander 16 points

If i am not mistaken that has a 7inch prop, it should be fine BUT look into this one: FC 28-12 Brushless Outrunner 1534kv, and use this prop:APC style propeller 7x6-E. it will give you MUCH more speed than the stock motor. it pulls 16 to 18 amps, so a minimum 25 amp esc is perfect.

 n8ander 16 points

Also, it has a 3mm shaft, so make sure your prop will fit a 3mm shaft. or buy the one I suggested. If you use a prop saver, put the prop saver on AFTER the propeller, that way your prop doesnt fly off if the prop saver breaks. A collet adapter would be better.

 Javier 9 points

High timming definitily.. it works on medium too with no problems, but i found it works a bit better with high. For the number of poles is also suposed to be high

 n8ander 16 points

This www.link this www.link my 30inch wing go 73 MPH

 n8ander 16 points

That didn't load correctly. Search: FC 28-12 Brushless Outrunner 1534kv,AND APC style propeller 7x6-E That motor and prop combo will give about 75MPH

 n8ander 16 points

OH, but if you are using this on the AXN floaterjet, a 7" prop will be too big. sorry.

 wayneuk 294 points

yes its fitted & not removeable a alloy prop holer also fits on the end with no problems

 jakobø 73 points

So no need to order another propholder?

 wayneuk 294 points

not really ..but i perfer the alloy ones so iam not relying on a o ring to hold my prop on. only a few $

 Ramron 932 points

yes, get a 3mm colet prop adapter, that will work better in the long run given the motor is located on the top of the aircraft and not the nose.