|
6/11/2010
RENI (32%)
It did not work with E-Sky radio system (Futaba) and Corona synthesized receiver RP8D1. Only with transmitter and receiver JR. What should I do? Thank you.
|
|
|
| |
|
gardleopard
(50%)
Mine did not work with my RP4S1 either. I don't know why, it works fine with other receivers I have. I only tested it on 2S, maybe the corona receiver deliver to low voltage?
|
|
|
|
Was this the best answer? YES | NO
|
|
 |
|
|
 |
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
| |
|
eclipce
(76%)
yes it will work on any radio. You only need on you receiver a futaba or jr connection
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
Niels
(54%)
It should work on any receiver. just have to pick the right channels on it that correspond to the control sticks on the transmitter. using gyro's in combination might be problematic.
Also make sure the wiring is in the right order(- signal)
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
gardleopard
(50%)
Yes, I'm currently using it to get elevons on my futaba skysport 4.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
3/10/2010
clovis (39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
|
|
|
|
|
9/21/2009
Philip (77%)
Will this mixer work with a HC 6 channel transmitter? I would like to use this with a fun jet, or some other plane that needs elevon mixing.
Phil
|
|
|
| |
|
clovis
(39%)
Hello, this mixer works with futaba 4 channel radio?
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
7/31/2009
laserist (45%)
I bought one of these as well as a pair of Turnigy TG-380 Aeroplane Gyros to stabilize the pitch and roll of my elevon delta wing FunJet.
Setup:
-Multiplex FunJet
-Spektrum DX5e / AR500
-Turnigy TG380 gyros
Having trouble getting this mixer to co-operate with the gyros, disabled on-board mixing, when pulling down on the elevator stick the elevons work correctly but pushing up on the stick causes the elevons to move erratically. Same problem when moving the stick left-right moving left the elevons perform normally but moving the stick right causes them to move all over the place.
Someone commented in the reviews that the gyros might introduce signal delay which confuses the mixer but I am unsure as to how to correct this.
Without gyros the mixer works perfectly. Anybody with any suggestions?
|
|
|
| |
|
laserist
(45%)
One more thing...
With only one gyro (either pitch or roll) it works perfectly, just not with both.
|
|
|
|
Was this the best answer? YES | NO
|
|
| |
|
MarcusRjCharita
(79%)
I did not buy mixer yet but I was looking for the same solution. Look at these two threads at RC groups:
962816 and 1115350
There r lots of solutions. Some quite expensive some creative. Pls tell me if the "angled gyros solution" works. :P
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
|
5/6/2009
Sergio (56%)
I want to know if these v-tail works with a futaba attack 4 AM?
|
|
|
| |
|
Photopigiste
(67%)
Hi Sergio! i have a Futaba 4NBL , it' s an AM TX too and i think AM must work too cause it' s not choose the modulation between AM FM PCM and 2.4GHz !
For it' s cost , try it ! You will see !*)
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
pauljam20 (45%)
I've just bought one of these. I have got a HITEC Neon-SS radio and Hitec servos. It works fine provided I only plug in one servo, if I plug in two they jitter, then go to full travel. Does anyone know what the problem is please?
|
|
|
| |
|
warwolf
(21%)
Warwolf
Cris your HITEC Neon-SS has Delta Wing and V-Tail mixing you must remove the back cover to get at the switch's.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
|
Juan (42%)
Hello,
It can work with standard or high torque servos?
|
|
|
| |
|
JRBeaman
(80%)
Mixers and gyros only process the information signal, and do not provide or change any power capabilities of the servos.
|
|
|
|
Was this the best answer? YES | NO
|
|
|
|
|
|
.jpg){kind=small}
