APC style propeller 10x5-E

 psguardian 34 points

Yes there is actually. sku # 074000049 is APC style 10x5 R.

 psguardian 34 points

These can be used as pusher props if you have a rear facing motor, just make sure the labels are facing forwards & the motor spins correctly. I used on a flying wing with rear motor, no problem.

 Kevin 7 points

I would use a different prop. The " APC STYLE" props are not very good, unless you plan to fly fast. It should fit on that motor, there is a small chance you will have to drill, or fill it in a little bit. Hope it works :)

 Pushrod 589 points

I think this prop would be a little to big for this motor.There a inserts supplied with these props to suit different size prop adapters.You need to buy a WATT Meter to see what ampage your motor with 10x5 prop and motor are pulling.

 Ale Kerger 10 points

Otima Helice recomendo

 marios 9 points

this prop is use with this motor. i use 40 amp ESC and 11.1 nanoteck. it has exelent performance!

 KaosKane 1442 points

Yes a little too big for 1400kv more for 11-1200.. BUT if u buy a hk wattmeter then run the motor up to the 210w max and then note throttle position (say 70pcnt) u can set throttle to 70pcnt of max using tx and off u go all safe

 Victorvs 953 points

quality is very good. IMHO

 smartguy 278 points

i recived my 3 props today and i was inpres about the quality, i will buy in the future more
Realy realy strong !

 Ednilson 1 points

I have a setup that works great, good for trainer Lipo 3s 20c 2200mAh Esc 40 prop 9x5 980 g

 Lindsay 22 131 points

I use this with the Turnigy G10 1200 Kv outrunner, I get about 1800g of thrust, and it it ballanced perfectly, and my setup goes over 10,000 RPM

 Vladimir 2 points

It is rather heavy if compare with GWS propellers.

 underthetire 410 points

Good quality, but check balance. I had 2 that were out quite a bit in the hub area.

 Shura 122 points

quality is very good

 Sergey 6 points

The best propellers (the price - quality)!!! Long ago on them I fly, it is very happy. But as well as any propeller - it it is necessary to balance. If by the plane there is no chassis - it is necessary to put a brake on a regulator, differently they will break (fragile).

 mike11444 5 points

nice quality

 minuteman 100 points

Ther are no stupid questions-only stupid answers :). You must look for pusher props like those: www.link sure to use the same size and brand for clockwise and counterclockwise rotation.

 gmango 44 points

Thanks heaps for the heads up. BTW, the link did not work. Ill do a search for pusher props and see what i can find.

 underthetire 410 points

Im no quad copter guy, but these are pretty stiff props, and find them to be way out of balance. Might want to check the gws props, lighter and they have pushers available.

 gmango 44 points

sweet. thanks, one last question. as the units on the GWS props are in mm, what unit of measurement are these props in? eg '10x5'? is that inches?

 underthetire 410 points

Yes, in inches.

 alisson 20 points

Existem pacotes de helices que já vem normal e contra-rotate...

 Simon 5 points

As already said, your after specific pusher props for your quad

 Haxxel 38 points

I would say its very stiff but not brittle, i crashed pretty hard with my pusher-prop plane, and the prop dug down in to the ground. The prop didn´*t got a scratch, but it ripped out the the motor from it´*s screws!

 underthetire 410 points

I would call them stiff, but pliable.

 Martin165 86 points

There are 2 kinds of props. One will have an "E" on the end, the other will not. The "E" means for electric use. Electric props are more flexible than nitro/gas props and lighter. The electric engine shafts are not as robust and are more prone to be bent when using nitro/gas props rather then "E" rated props (nitro/gas props are also heavier and add more load to the electric engine as well).

Hope this helps.

 190593 27 points

Yes they are flexible.

 Simon 5 points

i find them fairly stiff compared to the apc equivalent. They can be out of balance so always balance these before use.

 Juan 5 points

Perfect for PARK MASTER 3D

 bob shark 18 points

Certainly. Depends on the nature of your flight.

 newheliguy 7 points

These work great! Can't beat the price.

 HomerMix 47 points

sure, you can

 mctruk 188 points

Top little prop, it goes around and pulls the plane along. Price is wallet friendly and most of the ones i recieved are balanced well enough to fly straight from the box.

 Adri-Gja 11 points

Can use without problems

 Jesus G. 9 points

BUEN PRODUCTO Y MEJOR PRECIO

 prateek 67 points

i bought some wood 10x6 product no. www.link

 HomerMix 47 points

Not yet, unfortunatly

 hubbie 5 points

I think you can find 10x6 Master Airscrew propeller E, in HK.

 Daddiekat 10 points

I have been using the 12x6 or 12x7 and cutting them down to the length I need. Round the tips and balance them properly and they are working very well.

 Adri-Gja 11 points

you doesn't still have here in the hk. good www.link

 heavyj 96 points

16g not counting any shaft adaptors