New Items 论坛
注册

Total Price

AU$ 0.00

购物车 0 购物车 0 Loading...

2804-210Kv无刷电机万向(适合的GoPro以简洁的风格相机)

2804-210Kv无刷电机万向(适合的GoPro以简洁的风格相机)

Shipped From:
  • USA
  • Global
QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 18.22
状态:
有货
SKU:
047000029-0
WANT FREE SHIPPING? Click here to find out more!

展望使您的视频平台,超流畅的?这是流畅的高极数为特定目的建造的无刷电机万向节的终极。

2804电机带有嵌入式安装,所以任何DIY到PRO项目是简单和直接的,它也带有预装标准母连接器,所以布线是在插上的那样简单。这是一个完美的比赛给我们的无刷万向稳定董事会和IMU。

该2804是100-300左右克(GoPro的风格)相机完美的大小。

产品规格:
波兰人:12N14P
KV(RPM / V):210
阻力位:10.4omh
重量:35克
线材:0.19毫米
扭矩:240克
底部孔中心距:16毫米和19毫米
顶孔中心距:12毫米

  • SKU 047000029-0
  • Brand Other
  • 重量 31.0000
  • 长度 35.00
  • Packaging Width 15.00
  • 高度 35.00
  • 千伏(转/ v)的 210.00
  • 最大电流( A) 0.00
  • 电阻( MH) 10.00
  • 最大电压(V) 0.00
  • 功率(W) 0.00
  • 轴(MM) 0.00
  • 长度B (毫米) 15.00
  • 直径C(毫米) 34.00
  • 可以长深(mm ) 10.00
  • 总长度E(毫米) 15.00

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Good motor, I use it for roll in a 3 axis gimbal, I enlarged the threads to 3mm though. very simple to do, just disassemble the rotor and insert a 3 mm tap, work slowly, add a bit of oil. No predrilling required. Assemble it back. Bought two, one had a minute play if you pulled on the rotor casing, just put it on a board of soft wood rotor down and slightly tap it with a small hammer on the shaft (circlip end, do not remove the circlip) checking for play. Adjust the hammer power by slightly increasing it if there's still play. Don't over do it!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good motor, I use it for roll in a 3 axis gimbal, I enlarged the threads to 3mm though. very simple to do, just disassemble the rotor and insert a 3 mm tap, work slowly, add a bit of oil. No predrilling required. Assemble it back. Bought two, one had a minute play if you pulled on the rotor casing, just put it on a board of soft wood rotor down and slightly tap it with a small hammer on the shaft (circlip end, do not remove the circlip) checking for play. Adjust the hammer power by slightly increasing it if there's still play. Don't over do it!

I used these for a decently heavy 3D printed gimbal of my own design. The camera housing weighed 325 grams and these motors worked fine, but was nearing the threshold of over-drawing the 500 mA max that the Tarot gimbal control gives. I tried to use these motors on a 425 gram camera and they would not stabilize the gimbal within the 500 mA allowance of the gimbal controller.

If you decide to design your own gimbal, these will work great on cameras in the 100-300 gram threshold. Remember that gimbal design is mostly about balance than it is about torque. Also, the more jostling your quadcopter or craft does, the more torque you have to put out. So, test your stuff on the ground liberally before flying it!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I used these for a decently heavy 3D printed gimbal of my own design. The camera housing weighed 325 grams and these motors worked fine, but was nearing the threshold of over-drawing the 500 mA max that the Tarot gimbal control gives. I tried to use these motors on a 425 gram camera and they would not stabilize the gimbal within the 500 mA allowance of the gimbal controller.

If you decide to design your own gimbal, these will work great on cameras in the 100-300 gram threshold. Remember that gimbal design is mostly about balance than it is about torque. Also, the more jostling your quadcopter or craft does, the more torque you have to put out. So, test your stuff on the ground liberally before flying it!

these motors should have high quality bearings with no clear ens to the axles images are shaky and a lot of wobble, my next motors will be of a higher quality

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

these motors should have high quality bearings with no clear ens to the axles images are shaky and a lot of wobble, my next motors will be of a higher quality

meka kama nahe podi e ne neda

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

meka kama nahe podi e ne neda

I bought 6 units of this motor and only 2 of them work. The windings are open on the rest. Hobbyking needs to improve quality checks ASAP ! I also bought 3 controller boards and 1 unit came with a DIODE bad. Had to replace it myself.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought 6 units of this motor and only 2 of them work. The windings are open on the rest. Hobbyking needs to improve quality checks ASAP ! I also bought 3 controller boards and 1 unit came with a DIODE bad. Had to replace it myself.

Perfect motor for GoPro H3 (Roll-axis). Buy the smaller motor for pitch.
Smooth and silent. Very happy with mine.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Perfect motor for GoPro H3 (Roll-axis). Buy the smaller motor for pitch.
Smooth and silent. Very happy with mine.

enfin ces moteurs chez HK , la on va pouvoir ralis ces propres nacelles a moindre cot comme d'habitude chez HK.
merci

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

enfin ces moteurs chez HK , la on va pouvoir ralis ces propres nacelles a moindre cot comme d'habitude chez HK.
merci

047000029-0 -43040.JPG Download [81]

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save