注册

Product Finder

设置

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
注册

5W蓝色LED合金带材150毫米×12毫米(3S兼容)

5W蓝色LED合金带材150毫米×12毫米(3S兼容)

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
重量:
10
SKU:
371000068
产品介绍

5W蓝色LED合金带材150毫米×12毫米(3S兼容)

眼镜:
外形尺寸:150×12毫米
重量:8g
连接器:JST
光束角度:120
功率:5W
色温:460-465nm
电压:11.1V-13.5V(3S Lipoly)
电流:300毫安
光通量:400-450LM
显色指数:70-85
材质: 铝板
使用寿命:50000小时
工作温度:-20 - + 60摄氏度

*注:请确保电流消耗低于300毫安低于或损坏的危险LED灯条
Product
Specifications

额外信息

  • 商品编号:
    371000068
  • Brand:
  • 重量(g)
    10.00
  • 长度
    155.00
  • 宽:
    5.00
  • 高度:
    25.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I run them with a Meanwell LDD-300L (http://www.meanwell.com/mw_search/ldd-l/LDD-L-SPEC.PDF) switching DC current driver to ensure the leds are driven within rating despite the battery voltage (you can run them from about 10V to 36V input voltage). They are very bright, but only heat up to about 40C. Additionally, this driver has a PWM input (up to 1Khz, not servo-PWM) which I have connected to a GPIO of my Pixhawk flight controller using a N-FET inverter (the GPIO can't drive the current neccessary for the PWM input, I've used 100 Ohm in series to the gate for protection, 100K pull down on the gate and 1K pull up to the battery voltage on the drain). Using the PX4-built-in application gpio_led, the led stripes begin to blink when the battery reaches a low voltage.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Extreme Bright ! be careful, the polarity its reversed on JST connector, you must solder a 4.7ohms/1W in series to avoid overheating. Do not look directly over short distances
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Awesome for brightness! I read some of the reviews and thought I could deal with the heat... Unfortunately it gets so hot on 3s the solder melts and the wires fall off! Too bad, because they look great. Totally unusable.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This thing is very bright but way too hot. I'm not sure what you could put this on without damaging it. Certainly not foam it would melt it seconds. Only the red color stays cool but it has what I think is a regulator in line.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
ridiculously bright which is cool BUT COOL the lights aint, as mentioned in the other reviews they get WAY too hot and will drain a 1000mah 3S in about 2 mins..... Tried it on 2S but it barely lights up, guess will have to try a 9-10v set up but not too sure what to do, any suggestions?
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
WAY TOO HOT TO HOLD!!! would probably melt your airplane. These are super bright!! LOOKS AMAZING!!! I would like to mount 6 on my hexcopter, but they will need a WAY bigger heat sink... REALLY HOT!!!!!!! did I mention how awesome they look though?!?!?!?
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I just got this and tested it. It's super bright but it gets very hot really fast so I'm not sure how well this will hold up.
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。