New Items 论坛
注册

Total Price

AU$ 0.00

购物车 0 购物车 0 Loading...

(已完成)Sbach 3421900毫米气体的30cc(ARF)

(已完成)Sbach 3421900毫米气体的30cc(ARF)

Discontinued Product

Please continue searching for a similar product.
SKU:
Sbach342_3035
WANT FREE SHIPPING? Click here to find out more!

因为其对特技飞行到达现场的Sbach 342一直是不折不扣的感觉,菲利普Steinbachs masterpeice管理,以积极但优美的线条与现代的外观,已经引起航空爱好者在世界各地的想象力结合起来。性能当然是什么尖端特技飞行的飞机,这是具有讽刺意味的​​是,Sbach 342是专为模拟3D模型飞机的能力。

该Hobbyking Sbach 342是一个旁观者,这一点毫无疑问,你看一下细节越多,这种模式的“哇”的因素真的不知所措。控制面的大小抓住你的注意力马上,这是专为3D /精密特技飞行,再看看硬件,与球环节,复合喇叭,合金伺服喇叭扩展,螺丝扣推杆拉/拉舵等所有确认的初步印象。令人惊奇的,超高品质的建筑给人心肌力异同与轻量相结合,另一个重要的精密特技飞行箱打勾!

这种模式已经被寄望考虑和设计,值得一提的其他功能复合/股底盘安装,CF起落架,尾轮支架和水平安定面管,高档尖罩,碳纤维翼管,用螺钉固定树冠和磁体,用于调谐的消声器,包括消声器托架等选项,Hobbyking Sbach 342尺度细节,高品质的做工,高品质的元件和不折不扣的性能令人惊叹的组合。

眼镜:
翼展:1900毫米
长度:1850毫米
机翼面积:69平方分米
飞行重量:5400克〜5700克
4通道

包括:
所有硬件
整幅照片及光盘说明书

要求:
你自己的6通道TX / RX
6×标准尺寸MG高扭矩数字伺服
30CC〜40CC汽油发动机
RX电池
UBEC /稳压器
75毫米微调

  • SKU Sbach342_3035
  • Brand -
  • 容量(mAh) -
  • 重量 7680.0000
  • 长度 1390.00
  • 290.00
  • 高度 530.00
  • Sbach 342 22m

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

I maidened my Sbach today. First impressions with the build were very good. I liked the quality of the hardware, and the model was light and seemed to be well thought out. HOWEVER, I very nearly lost it on the first flight with full flutter of the tailplane! I was not flying it fast or hard, and it was during a power off, split S that the flutter occured. By the time I got it back on the ground, total flight time would have been less than four minutes, and inspection revealed all the fuselage formers shattered aft of the wing..... I'm going to repair and beef it up, but I'm disappointed that I should need to. I'm running an OS 1.6FX, which has very little vibration when compared to ANY gasser, so I'm shocked with the event. Other than that, the model flew very well and I'd have been well pleased if it had not fluttered.

I wouldn't recommend this model.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I maidened my Sbach today. First impressions with the build were very good. I liked the quality of the hardware, and the model was light and seemed to be well thought out. HOWEVER, I very nearly lost it on the first flight with full flutter of the tailplane! I was not flying it fast or hard, and it was during a power off, split S that the flutter occured. By the time I got it back on the ground, total flight time would have been less than four minutes, and inspection revealed all the fuselage formers shattered aft of the wing..... I'm going to repair and beef it up, but I'm disappointed that I should need to. I'm running an OS 1.6FX, which has very little vibration when compared to ANY gasser, so I'm shocked with the event. Other than that, the model flew very well and I'd have been well pleased if it had not fluttered.

I wouldn't recommend this model.

WE HAVE BUILT AND HAD THREE FLIGHTS WITH OURS AND ARE VERY IMPRESSED .WE TOO RUN A DLE 30 AND MY SON 3D IT WITH NO WORRIES.WE USED THE SUPPLIED HARDWARE AND HAVE NOT HAD A PROBLEM.TOP VALUE FOR MONEY AND AM LOOKING AT THE YAK 55 NOW AS WELL

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

WE HAVE BUILT AND HAD THREE FLIGHTS WITH OURS AND ARE VERY IMPRESSED .WE TOO RUN A DLE 30 AND MY SON 3D IT WITH NO WORRIES.WE USED THE SUPPLIED HARDWARE AND HAVE NOT HAD A PROBLEM.TOP VALUE FOR MONEY AND AM LOOKING AT THE YAK 55 NOW AS WELL

Well I finally finished this plane and i am very impressed with the quality.

I used all hardware except the hinges and pull pull cable for the rudder that came with the plane. I replaced the hinges with Pivot & Round Hinges 4.5x67mm. I replaced the cable with 27kg cable and cremps from BCF. I used a DLE 30cc engine with a 20x8 prop and had to make a plan for the standoff as the room between the firewall and cowling was very short. 30cc is more than enough for this plane to 3D.

See files for pictures and I will add a movi later.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Well I finally finished this plane and i am very impressed with the quality.

I used all hardware except the hinges and pull pull cable for the rudder that came with the plane. I replaced the hinges with Pivot & Round Hinges 4.5x67mm. I replaced the cable with 27kg cable and cremps from BCF. I used a DLE 30cc engine with a 20x8 prop and had to make a plan for the standoff as the room between the firewall and cowling was very short. 30cc is more than enough for this plane to 3D.

See files for pictures and I will add a movi later.

Sbach Manual Download [1452]
Dry fitted Download [3015]
CDI Ignition Download [2229]
sbach342 35 cc Download [189]

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!