注册

Product Finder

设置

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
注册

D922MG数码金属齿轮舵机1.8千克/12克/ 0.07sec

D922MG数码金属齿轮舵机1.8千克/12克/ 0.07sec

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
重量:
23
SKU:
D922MG

acc
产品介绍
专为在输出齿轮用于更好的强度直升机和快速响应applications.Steel材料,降低输出偏差后很长一段时间use.It高品质电机允许在高速运行更长。兼容多种陀螺仪,如双叶401601。
型号:D922MG
工作电压:4.5V / 6.0V
工作电流:50mA /180毫安
空闲电流:5mA
堵转电流:600毫安
运行速度:0.09sec.60º/0.07sec.60º
失速扭矩:1.6kg.cm / 1.8kg.cm
尺寸:22.5x11.5x24.6mm
重量:12克
死区:≤3uSec
装备: 金属
连接线:210毫米
工作温度范围:-20°C至+ 60°C
Product
Specifications

额外信息

  • 商品编号:
    D922MG
  • Brand:
  • 重量(g)
    23.00
  • 长度
    45.00
  • 宽:
    45.00
  • 高度:
    45.00
  • 速度(秒/ 60deg )
    0.07
  • 扭矩(公斤)(最少0.01公斤)
    1.80
  • Unit Weight (g):
    12
  • A(毫米):
    31.00
  • B(毫米)
    22.00
  • C(毫米)
    28.00
  • D(毫米):
    11.00
  • E(毫米):
    32.00
  • F(毫米)
    19.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Amazing finally installed a servo on the tail of hk 250 that works, I was about to send to the trash hely
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
For the price my absolute favourite! only issue is the bad soldering!! put evidentially some hot.glue at intern wiring and then you are safe. totally compares to 264mg savox!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I guess you need to give a good rating to have your review posted, anyways I tested the servo speed and it is .15 at 5v not even close to specs. I then ran the servo continuous and about a minute in it started cycling erratically, maybe I got a dud as it has good reviews but mine went in the trash and I won't be buying them again
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I bought three of these to replace my 933's on a 450 Pro, after two were damaged in a crash.

The 933's were pretty good servos - smooth running with good centring, very little backlash in the gears and a perfect fit in the 450 Pro. On the downside, they seem to have fragile cases. I'd recommend using the HK servo arms, which are thin and quite flexible, and might offer some protection to the servo in a crash. You can use a back nut on the ball link bolt.

The main reason I decided to try the 922's was that the 933's were a bit slow - showing only 0.13s @ 5.9v on a servo tester.

I was therefore shocked to see the 922's show almost the same speed in the servo tester - 0.125s @ 5.9v.

Not only that, they also sound really harsh and rough, and have far more backlash in the gears than the 933's. I find it hard to believe they come from the same supplier.

In flight, on my 450 FBL, I had to reduce cyclic gains by 10 points from the value I'd used with the 933's, otherwise I would get a severe cyclic shake.

I also made the mistake of only ordering 3 servos - and the one I installed in the right aileron position oscillated around centre. After about 20 flights, it decided to shift it's neutral by about 30 degrees.

Overall, therefore, I think the 922's are nothing like as good as the 933's. I've since replaced them with Corona DS-929MG's. Although the Coronas have slighly more gear
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I tested the servo and found it to be .15 on 5v nowhere near the stated speed, followed by running it continuous and it lasted about a minute before it started cycling erratically. Not worth sending back so it's in the trash.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Ottimo servo, robusto e preciso, l'ho utilizzato per gli alettoni del mio Funcub Multiplex, dopo un forte crash in picchiata i servi non hanno subito alcun danno e fanno ancora un'ottimo lavoro :-)
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Buon servo per il ciclico.

veloce e preciso e poi costa veramente poco.

Mi sa che ne compro ancora
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
There have been many discussions about this servo on major web forums. Mostly, people don't read the specs that this is not .09/sec at 5V and only .07 at 6V. Theory aside, this is an awesome cyclic servo for a 450 class as it has a smooth and precise movement. It is "OK" as a tail servo on a 250, but a faster servo would be better. Overall, great value and great servo.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
it is fast servo and powerful but not as torque of DM 933
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
tima qualidade, uso em um HK 450, apesar de no fazer vos 3D ainda, para hovers perfeito. Segundo outros colegas, pode fazer 3D com estes, sem problemas.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

acc

产品标签

使用空格分隔标签。使用单引号(')标注词组。