注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • USA

EP环氧滑翔机W /电机1410毫米(插销N飞)

EP环氧滑翔机W /电机1410毫米(插销N飞)

QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 236.94
Rating:
Stock:
重量:
1930
SKU:
189000038

Price War

产品介绍

一个很好的形成环氧荚和动臂式的滑翔机轻和光层的翅膀,3×9克舵机预装了副翼和电梯的功能外,还包括预装28-36 1800kv NTM螺旋桨驱动的无刷外转子与20A ESC。


机翼和尾翼构造质量好轻和光层,还搭载前置铰接控制面。

所有硬件包括在框获得在空中滑翔以最小的装配。本发明提供一种碳翼梁和碳看热潮。正如任何适当的滑翔机,机翼很容易在现场可移除的产品快速组装/拆卸,这使得运输和存储变得轻而易举。

您只需要添加自己的Tx / Rx和锂聚合物电池来获得在空中滑翔。

特征:
•机身环氧树脂
•碳纤维外观热潮
•翼可拆卸,便于运输
•无刷电机及折叠9×6道具W¯¯包含/微调
•3个9克伺服

眼镜:
翼展:1410毫米
长度:704毫米
电机:28-36 1800kv无刷NTM的外转子(含税)
ESC:20A
飞行重量:450克


需要:
4路发射器和接收器
3S 1800〜2200mAh的锂聚合物电池

Product
Specifications

额外信息

  • 商品编号:
    189000038
  • Brand:
  • 重量(g)
    1930.00
  • 长度
    1030.00
  • 宽:
    160.00
  • 高度:
    235.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
When this arrived the tail was broken off,and needs extensive repair.The elevator rod is to stiff to work and will also need attention.There is no method of attaching the canopy,just a bit of wire glued in,but that doesn't work.It was obvious the tail was broken before despatch,and the other things are just poor design and thought.Very disappointed with this product.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
MODEL IS VERY BEAUTIFUL, BUT SOME COMMENTS, THE RED BAND IS A PAINTING AND STRIPS VERY EASILY, THE SERVANTS NOT GOOD QUALITY ARE BUT RUNNING, THE ENGINE IS STRONG AND ENOUGH TO RISE VERTICAL, ESC OF 20A heats A LITTLE, AND The HOME THE FLIGHT iS VERY sTABLE and docile, wORTH A BUY
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I am disappointed very poor quality.
one servo does not work
a flap has a small travel
fixing the wing, impossible to assemble
empennage assembly through 3degrer
esc too small
corvering Film full of air bubble
no assembly instructions
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I replaced the stock ESC as it was getting quite warm just sitting on the bench with the battery plugged in and replaced the stock props with 6x4 ( https://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=13130 ). Assembly took one evening. Build quality is OK but the horizontal stab is a bit flimsy and slightly misaligned, the balsa construction is quite good as is the composite pod. Flies quite well and thermals nicely with a 1300mAh 3s. I will probably add rudder at some point or program in some differential aileron to correct for adverse yaw.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Not the best glider out there but with a lit bit of work you can actually fly it some day :)
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Several defects found when finishing assembly. Vertical stabilizer was cracked, horizontal stabilizer was warped, elevator servo and control rod were stuck (glue in control rod line), the brown paint freely chips from mono coat, control arms for ailerons not long enough (connection touches the wings lower surface). No flights yet, seems to have more than enough power. Then the price drops a week after purchase. A file with some minimal instructions would be good (no CG info).
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very disappointed in this model. Quality is very poor for the following reasons:
1. Two out of the three servos were bad out of the box.
2. Tail section is glued in place approx ten degrees off. Vertical stab and horizontal stab do not align with fuselage and wings.
3. Paint chips were falling off out of the box and continue to fall off, even on the bench which I have covered with a towel. The paint definitely does not have enough elasticity properties. This thing looked like a beater plane BEFORE it was ever flown!
4. No instructions what so ever. No idea where to set throws or CG. This model takes very small throws on elevator and ailerons so be cautious. Also, there is a set screw that holds the prop on the motor shaft. You will not see this initially as you have to disassemble the prop adapter to find it.

With all the work this plane has taken on the bench to fix all the bad quality issues, I would have preferred an ARF. It would've been faster to build than to repair and I would have used better components.
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Manual download now [14.14Mb]

产品标签

使用空格分隔标签。使用单引号(')标注词组。