这是一个不错的大小F-15与ARF已经为你做，并提供了70毫米EDF单元，全面的硬件套件和机械缩回集，独特的喷漆方案，让您以满足您的choice.To的动力传动系和伺服的从这个模型中最好的，你将需要寻找设立了4S，并且由于高伺服计数，特别是如果你选择，以适应所提供的缩回，我们强烈连同一个5A UBEC建议的OPTO ESC为RX功率。规格：翼展：750mmLength：1100mmWing面积：12dm2Wing负荷80克/ dm2Flying重量：950克4〜5个通道（油门，升降舵，副翼，转向，缩回）包括：需要机械缩回的带轮子的所有Hardware70mm EDF风扇UnitColour /照片说明BookletSet ：您自己的Tx与Rx28mm EDF无刷电机4S（4毫米轴）9×9克伺服+ 1×17克Servo45A〜60A ESC5A UBEC2200mAh 4S Lipoly电池
For start the assembly instruction are very poor quality, spacialy for the retracting gear set-up, goody's for servos are not fitting with mine
so i have to put mine, missing some parts for df unit installation, rear landing gear has to be modified to fit as well as to foam body, lading gear are the same as for the f-16 actually, glue was almost fully dry
but i was planning to use mine anyway, on mine no thrust vectoring
with a 60a esc the plactic protector on the bottom is not big enought
wirering on the motor is not fitting with the hole on the foam, bit of rework to do here and there.
for my first assembly kit it's a good chalenge, hope everything turn right with it.
assembly should be finish soon as well as the spring here in quebec
follow up on maiden flight later.I think this F15 is a great buy. I left the landing gear off and moved the battery forward leaving the battery bay for the receiver. If I were to mount the landing gear I would bend the main gear straight and use the Variable rate knob on my transmitter with a bigger servo. The noise gear needed some work too, but all in all it was a great project and a very nice flying airplane.Just forget about the landing gear is app 177 g, the bird have unlimited capacities and fly real scaleE' un modello che non lo consiglio dicono che i carrelli sono retratti ma ce da lavorci molto perch non entrano nella loro sede sono da piegare e tagliare a meno che non li lasciate fissi, per aprire la fusoliera bisogna tagliare i due copri vettori perch incollati non riesco a capire la necessit visto che bisogna metterci il motore, la qualit comunque scarsa.Don't waste your money on this, of course its cheap but still the quality of the plane doesn't compliment the price tag.
Very cheap foam, main landing gears do not fit in the compartment...
you cant have much choices with the batteries as the battery compartment has limited space....Hi:
My setup for this is:
Hobby King 60A ESC 4A UBEC, EDF Ducted Fan Unit 5Blade 2.68inch 68mm, 4 HXT900 servos, and Turnigy 450/500 H2223 Brushless outrunner 4400KV, 4S 2200mAh 45C B Grade lipo. No landing gear, hand launch setup.
Airframe plus motor plus servos plus ESC, 740 grms. Battery plus Wattmeter 340 grms. AUW 1080 grms, max 940 watts 62 Amp, unlimitd vertical, I guess aprox 1300 grms of thrust with edf mounted inside plane.
Brittle foam easy damaged even for a little bump.
This setup is amazing (at least for me). Easy hand lauch, and good speed (not measured).
Motor and ESC reaching its limit. Very hot ESC, motor warm to hot.
3 to 4 minutes of flight with reserve for two landing attempts. Only 5 flights, I return with more comments on next fligths.
Motor and EDF 2 hours of work for correct balance. Balancing is a must.