注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global
  • USA

FPV赛车无人机PDB带OSD BEC的CC3D

FPV赛车无人机PDB带OSD BEC的CC3D

QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 16.06
Rating:
Stock:
重量:
10
SKU:
571000099-0

Price War

产品介绍

这个多功能FPV无人机PDB为了您CC3D飞行控制器已经被设计成具有赛车的性能和可靠性。启用明快,扎实的供电到您选择ESC年代,也是进出照相机供电,发射器的LED等。

电源可以从2S至6S LiPoly电池供电,并支持屏幕Diplays(OSD)显示电压,电流,定时器和RSSI。

OSD支持MWODS固件像Cleanflight,Betaflight&Baseflight。

这是一个防弹PDB带OSD为您FPV赛车的无人驾驶飞机。

特征:
•配电板+ 5V / 12V BEC + OSD
•支持2-6S输入电压
•2oz覆铜铝箔,4层板,以确保大电流的基
•双BEC,5V / 12V
•OSD功能,支持KVteam MWOSD固件,自带FTDI
•支持OSD功能,例如基本的电压,电流,定时器和RSSI。
•36×36毫米大小,相同的安装孔为Naze32,CC3D,SP3

眼镜:
输入电压:5-24V DC(2-6S LiPoly)
BEC:5V / 2A&12V / 2A切换
最大分布电流:70A常数,100A突发
外形尺寸:36×36×4毫米
安装孔:30.5×30.5毫米M3(标准)

重量:7.3克

Product
Specifications

额外信息

  • 商品编号:
    571000099-0
  • Brand:
  • 重量(g)
    10.00
  • 长度
    80.00
  • 宽:
    5.00
  • 高度:
    60.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

Quality
Value
Overall
I received the board fairly well packaged and flashed it with the latest MWOSD firmware as per specification. The board was flashed successfully, as well as programmed. Then it worked ok-ish for a couple of times. OK-ish, because the fonts were not displayed properly, but that might be the firmware's fault, not the board's.
Anyway, what seemed stupid, and yes it's a strong statement, but that's just hoew it is, because if you look at the first picture at the left hand side corner of the board, you'll she a tiny tiny component soldered very very close to the mounting hole. When you screw the standoff for the FC chances are you'll knock that component of it's pads. So really not very well thought layout. Other than that could be a fine board.
Quality
Value
Overall
Quality
Value
Overall
This is basically a very good product and an excellent value, but I must give it a low rating because of a build quality issue. The chip that does the OSD video overlay wasn't fully soldered to the board. Most of the chip's pins weren't soldered at all, resulting in a very flaky video signal (which I originally blamed on my video transmitter/receiver pair). I was able to fix the unit by soldering the missing connections under a microscope, but that's far beyond typical hobbyist capabilities. Most folks would have to return the product at their own expense, or worse, would suffer an in-flight failure. Examine the unit under a magnifier before installing it!

Once all the parts were properly soldered and the board was cleaned and dried (dish soap, hot water, and a toothbrush, followed by blow-off with dry air), the unit works well. I'm using the Minoposd firmware with LibrePilot loaded on the HK CC3D Mini.
Quality
Value
Overall
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。