New Items 论坛
注册

Total Price

AU$ 0.00

购物车 0 购物车 0 Loading...

HKPilot 500mW的收发器遥测电台V2(433MHZ)

HKPilot 500mW的收发器遥测电台V2(433MHZ)

Shipped From:
  • USA
QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 69.84
状态:
有货
重量:
125
SKU:
387000077-0
WANT FREE SHIPPING? Click here to find out more!

包装500mW输出功率,这V2 433MHz的遥测收音机让你比如我们HKPilot兆或Multiwii AIO到USB或UART配备设备链接到飞行控制器,如电脑,笔记本电脑或平板电脑支持USB连接(OTG)。新的V2收音机,不再有单独的空/地模块,两个收发器可以使用UART或USB连接,并支持这两种模式。无线电设置,不仅可以让你看到实时数据,如覆盖在地图上实时GPS定位,系统电压,航向,航点导航甚至人工地平线和这么多。使用开源MAVlink地面站软件,你甚至可以用操纵杆通过计算机和更新设置,住飞你的飞机!或者只是用它为你需要一个无线串行接口DIY项目。该套件提供了一个很好的低价,更远的射程和卓越的性能。该系统采用433MHz的频段,并提供了使用HopeRF的HM-TRP模块运行定制的,开源固件全双工链路。

特征:
•可互换的空中和地面433MHz的模块
•微型USB端口
•6位Molex连接
•500毫瓦的最大输出功率(可调)
•-117 dBm的接收灵敏度
•SMA连接器
•2路全双工自适应通过TDM通信
•UART接口
•透明串行链路
•MAVLink框架协议
•跳频扩频(FHSS)
•可配置的占空比
•纠错校正到bit错误的25%
•开源SIK固件
•通过*任务规划和* APM规划配置

眼镜:
电源电压:3.7-6 VDC(从USB或Molex连接)
传输电流:500毫安27 dBm的
接收电流:25毫安
串行接口:3.3 V UART

包括
与天线两个无线模块
微型USB电缆
Android的OTG转接线
6线Pixhawk连接线
6至5位APM和PX4连接线
不干胶贴片

频率规定因国家而异,所以请咨询当地空域当局找出哪些频率在您所在地区的法律。

注:APM参考指ArduPilot项目,基于Arduino的开源计算平台,通过3DR和开源社区开发对一个家庭的开源自动驾驶仪。它由ArduPilot兆(APM)电子的选择和各种免费软件版本不同的车辆,并通过一个开放源码的创作共用许可的管理。

注意:这不是一个原始的Arduino品牌的产品。

  • SKU 387000077-0
  • Brand HKPilot
  • 容量(mAh) -
  • 重量(g) 125.00
  • 长度 110.00
  • 45.00
  • 高度 80.00

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

This item is very badly designed, it will make a lot of perturbations especially on the video transmitter and the OSD. This happens even if you put ferrites and use a separate power supply for this module.
Also it drains too much current to be used as is on a Smartphone.

It is possible to decrease the input power in the settings but even at a power lower than 100mW it will still perturbates the OSD and the video emitter.

Avoid this device, with the 433MHz antenna from immersion RC and a dipole antenna on the ground you will reach >7km range with the 100mW version from 3DR without perturbating your other transmissions.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This item is very badly designed, it will make a lot of perturbations especially on the video transmitter and the OSD. This happens even if you put ferrites and use a separate power supply for this module.
Also it drains too much current to be used as is on a Smartphone.

It is possible to decrease the input power in the settings but even at a power lower than 100mW it will still perturbates the OSD and the video emitter.

Avoid this device, with the 433MHz antenna from immersion RC and a dipole antenna on the ground you will reach >7km range with the 100mW version from 3DR without perturbating your other transmissions.

I'm getting 3km range with these radios with stock antenna on air radio and dipole on ground station! really great radios at a fantastic price!!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I'm getting 3km range with these radios with stock antenna on air radio and dipole on ground station! really great radios at a fantastic price!!

First set worked for 2 days (ground testing), then one unit stopped working. HK replaced it swiftly. Second unit is working so far, but I suspect they draw too much power for all my android devices, and as a result, dont work on android. Ive had it working once for a short while, but more typically they dont even power up on the OTG cable and if they do, sometimes my phone/tablet will instantly shut off. Tried many OTG cables, 3 different android tablets/phones. I worked around it by connecting a bluetooth module to the radio, and powering those separately, then connect via bluetooth. Setting the tx power in Mission Planner doesnt seem to work. Build quality is mediocre, the case isnt even held together with screws and comes apart too easily. Cutouts for the connectors are a bit small, and connectors can fall out. Nothing you cant solve with some hot glue and tape though. Range not tested so far, but probably excellent based on ground testing results. Oh, and beware, servo's dont like these radio's, you have to keep this unit well clear from servo wires or they will go beserk.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

First set worked for 2 days (ground testing), then one unit stopped working. HK replaced it swiftly. Second unit is working so far, but I suspect they draw too much power for all my android devices, and as a result, dont work on android. Ive had it working once for a short while, but more typically they dont even power up on the OTG cable and if they do, sometimes my phone/tablet will instantly shut off. Tried many OTG cables, 3 different android tablets/phones. I worked around it by connecting a bluetooth module to the radio, and powering those separately, then connect via bluetooth. Setting the tx power in Mission Planner doesnt seem to work. Build quality is mediocre, the case isnt even held together with screws and comes apart too easily. Cutouts for the connectors are a bit small, and connectors can fall out. Nothing you cant solve with some hot glue and tape though. Range not tested so far, but probably excellent based on ground testing results. Oh, and beware, servo's dont like these radio's, you have to keep this unit well clear from servo wires or they will go beserk.

Telemetry Radio Setup Download [2]
Setup Download [2]

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!