注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global

HobbyKing™弥数字高扭矩伺服MG6公斤/ 0.11sec /26克

HobbyKing™弥数字高扭矩伺服MG6公斤/ 0.11sec /26克

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 38.24
缺货!
Rating:
Stock:
OUT OF STOCK
重量:
53
SKU:
HK28013DMG

Price War

acc
产品介绍

香港弥系列伺服系统通过高精度的伺服技术代表下破。采用磁感应强度,而不是一个电位器,精确度和性能无与伦比的水平。

眼镜:
电压:4.8V / 6V
速度:0.13sec / 60deg(4.8V) - 0.11sec / 60deg(6V)
扭矩:5kg.cm(4.8V) - 6kg.cm(6V)
尺寸:35.6毫米点¯x尺寸仅为15mm×31.5毫米
重量:26.12克
电机: 低绘制无芯
齿轮传动系统: 全钛合金

弥:磁感应,代替传统的电位计(1877年发明)的使用磁旋转编码器。磁旋转编码器有更长的使用寿命,并遭受磨损少。

Product
Specifications

额外信息

  • 商品编号:
    HK28013DMG
  • Brand:
    HobbyKing
  • 重量(g)
    53.00
  • 长度
    90.00
  • 宽:
    15.00
  • 高度:
    85.00
  • 速度(秒/ 60deg )
    0.11
  • 扭矩(公斤)(最少0.01公斤)
    6.00
  • Unit Weight (g):
    26.12
  • A(毫米):
    32.00
  • B(毫米)
    36.00
  • C(毫米)
    30.00
  • D(毫米):
    15.00
  • E(毫米):
    50.00
  • F(毫米)
    20.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Just fitted these servos to my T-Rex 500. Fits perfectly. Appear to work just as well as the Align servos
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I bought four of these servos for a 1.4m wing span Turnigy Extra 260, hoping that they match the promising specification. The wings of the Extra need low profile servos or park servos for the ailerons. Metal gears, no potentiometer ... but unacceptable slackness of the gear. The same at all four servos. The gear as such seems to be o.k. but either the bearings or the fit of the bearings in the plastic casing require attention. The servos may be o.k. for a slow flyer but definitely not for an aerobatics plane.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Using these as cyclic servos for a Gartt GT500TT-FBL kit (same as HK GT500) seem strong enough to move swash and blades and fit perfectly back to back in a 500 class heli.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
For airplanes that have a good size to use servants of great people, make sure that your servant will not jump teeth to reseber some pressure because it has its all-metal gears, high quality.For airplanes that have a good size to use servants of great people, make sure that your servant will not jump teeth to reseber some pressure because it has its all-metal gears, high quality.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
So far these have worked great with my robird FBL gyro. They run fine at 333hz and don't even get warm. The gains can be set high without causing the shaking you get with cheap inaccurate servos with FBL systems. They do growl a lot at rest but almost all digital servos I've seen do this.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
These servos appear to be a 9250 clone with a small daughtercard with a sensor chip on it replacing the pot. I don't know if the electronics are actually cloned or are diffrent but the case and gear train are the virtually the same. The top cap is just different enough that I couldn't use a Fitec 9257 top cap without the servo sounding like it was in pain when the gears moved, something was too tight with the case assembled this way. There is a small plastic bracket with a bearing that holds a shaft with a magnet on the end that goes through to the main output gear. The magnet sits just above the daghtercard and chip and apparently this chip can sense the magnet rotating on the shaft. One thing I like about these is that without the pot there's nothing that can physically go wrong with it. As others have said there is about 0.3 to 0.5mm of side to side slop in the recess in the top cap that holds the ball bearing. you can try to use a bit of CA to build up the sides but care must be taken to not use too much because if you press the bearing down it creates drag on the output shaft. In my opinion it's better to just leave it as is because 0.3mm of side to side slop won't have any noticeable effect on flight performance, especially in an FBL system (most servos have more than that in gear slop after a few dozen flights anyway, and this is side to side not rotational slop so it do
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Great Servos,
Very smooth movement and can be mod to turn 180 degrees by changing an internal resistor.

I'm using them to modify flight instrument for a simulator.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Output shaft on both my servos has a lot of slop due to the bearing being loose in the housing. Pulled them apart and applied CA around the housing and now its fine. But looks like I'm not the only one with this problem, sort it out HK! Otherwise its a fast powerful servo, no other issues.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
todavia no los us ....si con probador de servo actuan bien y rapidos recomiendo heli 500
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
super strong servo, very powerful!!! :)

verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

acc

产品标签

使用空格分隔标签。使用单引号(')标注词组。