注册

Product Finder

设置

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
注册

KDA 28-47 15Turn小号无刷内转

KDA 28-47 15Turn小号无刷内转

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
重量:
149
SKU:
KB28-47-15S
产品介绍

KDA 28-47 15Turn小号无刷内转

KB28-47-15S
轴尺寸:3.17毫米×12毫米
电机尺寸:27.6毫米毫米x 47毫米
重量:135克

电机规格。
KV:2600
空闲电流 :1.0A
阻力位 :0.0330
最大电流 :27A

Product
Specifications

额外信息

  • 商品编号:
    KB28-47-15S
  • Brand:
    N/A
  • 重量(g)
    149.00
  • 长度
    0.00
  • 宽:
    0.00
  • 高度:
    0.00
  • 千伏(转/ v)的
    2600.00
  • 最大电流( A)
    27.00
  • 功率(W):
    0.00
  • 长度B (毫米):
    48.00
  • 可以长深(mm )
    45.00
  • 最大电压(V)
    0.00
  • 轴(MM):
    3.00
  • Unit Weight (g):
    135
  • 直径C(毫米)
    28.00
  • 总长度E(毫米)
    60.00
  • 电阻( MH):
    0.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
It seem very good product, but this product is in back order. I with to use this motor for my BD5 plane. But don't know the setup is enough not. so have to try first.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Runs very true. No-load RPM on 5 cells is 56,000. Nice running. However the flat on the shaft, might be interfering with the impellor's shaft adaptor. On my edf's in use, these KDA inrunner's (2600kv here)(and my 4900kv) happen to have a dissipation factor that meets or exceeds the data. In other words they are meant for 500 watts input power, yet I have two in use at 850 watts (30 seconds) and can maintain long periods at nearly 800. With heatsink a 850 to 900 watt dissipation is considered. I have good success with these two motors. Well balanced. Dispite lack of holes for cooling, the case, itself happens to get rid of heat. By augmentation with a finned additional heatsink, there seems to be no problems. Not sure of the lifespan, but the bearings are high quality.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
A start only because here are no cooling holes in front/back of this motor. But if you want, you can simply remove front and back of this motor and drill own cooling holes.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Just received the motor. Going to put it in a stryker.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Hi , I have one in my Tarot 480 pro on 380mm blades , on 4S1P 2450mAh Lipol. It loads up to 60A , and nice very high power. But his minus is cooling, motor is hot. I dont know , how kHz i must set , to get him cooler.

But it has a lot of power.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Ordered this motor,hope for some good results in a EDF 70mm fan and EPP Jet 990 mm span, AUW about 800 g,lets see!,maybe better with a higher kv motor?,hope this one has better efficency than the Turnigy 36 series ones!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Good motor, worked fine at 900w on 4s (5x5 tgs prop) with a heat sink on a funjet. There are lighter motors available, and without cooling holes, my suggetion is to go with another motor. This thing is a brick. Btw, I got this motor to see if it could match a 28mm ARC motor. This thing is not capable of being pushed hard. I tried it at 1300w on 4s, and it was waaaaay too inefficient, it acted more like a space heater and it almost fried. Enjoy!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Unbelievable power for this motor...

I have installed this into my Starmax f-18 tiger and against the stock unit this system produces 150% more thrust on half the Amps its unreal!!

People have said there are some cooling issues but I haven't come across any problems so far!

This is more like 7stars with price and is a great EDF upgrade..
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Four stars for lack of cooling holes.

BUT I'm running this motor in my Stryker with GREAT results. Hitting 110mph on 4S with 5x4 prop.

It's really a better 3S motor since you can run 6" props on 3S.

The front cap screws off, and the back cap can be knocked out from the inside to drill your own cooling holes. With cooling, I can run 4S, 60A, and the motor's hot, but taking it.

To run without cooling holes, stick to 40A on 4S or 50A on 3S (6x4
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I have one in my Eco Shark Boat, with a Gr.2318.26 prop its a beast! The Eco go out the water at full trottle. I run it with a 3s 2450mha (25c) lipo, the Eco weights is arround 800gr. Not too hot after 8 minutes of full trottle run, with a home made water refrigeration sistem. I run it with a 100A Opto esc and a Bec, buy in hobbycity. I check the max. Amp for this setup, for my Eco (800gr), is 30A in static.

Its a great outrunner!
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。