New Items 论坛
注册

Total Price

AU$ 0.00

购物车 0 购物车 0 Loading...

MultiWii SE V2.0飞行控制器瓦特/ FTDI

MultiWii SE V2.0飞行控制器瓦特/ FTDI

Discontinued Product

Please continue searching for a similar product.
SKU:
381000133
WANT FREE SHIPPING? Click here to find out more!

该Multiwii SE V2.0是加载功能陀螺仪/加速度计基于飞行控制器。随着扩展选项和完全可编程,该设备可以控制几乎任何类型的飞机。这是您的多旋翼飞行器的理想飞行控制器。

特征:
•体积小,35x35mm安装孔
•6个输入通道标准接收机和PPM SUM接收机
•多达8轴电机的输出
•2舵机输出俯仰和横滚平衡环系统
•可以利用伺服输出触发拍照键
•FTDI / UART TTL套接字调试,上载固件或液晶显示器
•I2C插座扩展传感器,I2C LCD / OLED显示屏或CRIUS的I2C GPS导航板
•独立的3.3V和5V LDO稳压器
•ATMEGA 328P微控制器
•MPU6050 6轴陀螺仪/加速计动作处理单元
•HMC5883L 3轴磁力计的数字
•BMP085数字压力传感器
•板载逻辑电平转换器

飞行模式:
•以下基本模式的一个
- 艾可
- 级
- Alt键保持
- 锁头
•可选模式
- HeadFree(陶然)
- GPS保持(需要GPS接收器+ I2C-GPS导航局)
- GPS返回首页位置(需要GPS接收器+ I2C-GPS导航局)

眼镜:
尺寸:40x12x40mm
重量:9.6克
固定孔间距:35毫米 (它可以通过CRIUS配电板改为45毫米)
钻孔直径:3毫米

包装内容:
MultiWii SE FC×1
USB编程板×1(必需的,但另售迷你USB电缆)
3PIN到1Pinx3电缆100毫米x 100 2
3PIN到3PIN线100毫米x 100 1


更多信息可以在Multiwii网站上找到。
http://www.multiwii.com

  • SKU 381000133
  • Brand -
  • 容量(mAh) -
  • 重量 30.0000
  • 长度 130.00
  • Packaging Width 10.00
  • 高度 90.00

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Never Buy it from them. they will send you

XZN MWC MultiWii SE Standard multi-Copter 4-axis Main flight con

http://www.geeetech.com/xzn-mwc-multiwii-se-standard-multicopter-4axis-main-flight-con-p-552.html

this board which is very poor and cheaper(US 19) than the item shows in their listing.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Never Buy it from them. they will send you

XZN MWC MultiWii SE Standard multi-Copter 4-axis Main flight con

http://www.geeetech.com/xzn-mwc-multiwii-se-standard-multicopter-4axis-main-flight-con-p-552.html

this board which is very poor and cheaper(US 19) than the item shows in their listing.

They sent me the wrong board the 1st time. Did a RMA to replace wrong board and they sent me the same wrong board again. Can't comment on functionality because I've never received what I ordered!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

They sent me the wrong board the 1st time. Did a RMA to replace wrong board and they sent me the same wrong board again. Can't comment on functionality because I've never received what I ordered!

Good board for my 20 cm. arm small tricopter flying great with D2822/17 kv 1100 motor and 1,5 Ah lipo pack for about 10 minutes of very fun.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good board for my 20 cm. arm small tricopter flying great with D2822/17 kv 1100 motor and 1,5 Ah lipo pack for about 10 minutes of very fun.

Hi All! I've got MultiWii 2.0 installed and running on my Quadro. HobbiKing Rx, HobbiKing 10A ESCs are used. Previously I used HobbyKing Multi-Rotor Control Board and it flied well. On this MultiWii control motors running not fast enough to take quadro off the ground. Even if I move throttle stick to the most up position it does not fly. Can anyone say what is wrong?

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Hi All! I've got MultiWii 2.0 installed and running on my Quadro. HobbiKing Rx, HobbiKing 10A ESCs are used. Previously I used HobbyKing Multi-Rotor Control Board and it flied well. On this MultiWii control motors running not fast enough to take quadro off the ground. Even if I move throttle stick to the most up position it does not fly. Can anyone say what is wrong?

Nice board flying very well But when I tried to plug the battery monitor on A3 input as shown on file "pin assignments" (lipo directly on this input) I burn the Atmega ...I had to add the divider resistor before input the direct lipo voltage.So be carefull bfore wiring this batterie monitor input (A3 pin).
I put a updated picture of the pin assignments with the rsistors in the file section

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nice board flying very well But when I tried to plug the battery monitor on A3 input as shown on file "pin assignments" (lipo directly on this input) I burn the Atmega ...I had to add the divider resistor before input the direct lipo voltage.So be carefull bfore wiring this batterie monitor input (A3 pin).
I put a updated picture of the pin assignments with the rsistors in the file section

I use this board on a 55cm quad, replacing a homemade combo of Arduino ProMini and 4 single sensors boards... Adding a LZ-GPS was very easy because I2C is brought out on its own pin header. The HK S2 V2 board has the Crius V2 layout and comes with preloaded MultiWii 2.1 firmware for Quad X constellation. Firmware can easily be updated or changed to any other config with the FTDI header and Arduino 1.01 software. The MPU 6050 gyro/acc gives really great and stable flight behaviour with an very smooth ACC level mode never seen before. BMP baro is not state of the art anymore (low resolution), but its OK to get a height hold mode within 2-3 meters. Overall: Great board with good quality, small boards size, totally worth the money. Will buy a 2nd one for my Flydumini as soon as they are on stock again.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I use this board on a 55cm quad, replacing a homemade combo of Arduino ProMini and 4 single sensors boards... Adding a LZ-GPS was very easy because I2C is brought out on its own pin header. The HK S2 V2 board has the Crius V2 layout and comes with preloaded MultiWii 2.1 firmware for Quad X constellation. Firmware can easily be updated or changed to any other config with the FTDI header and Arduino 1.01 software. The MPU 6050 gyro/acc gives really great and stable flight behaviour with an very smooth ACC level mode never seen before. BMP baro is not state of the art anymore (low resolution), but its OK to get a height hold mode within 2-3 meters. Overall: Great board with good quality, small boards size, totally worth the money. Will buy a 2nd one for my Flydumini as soon as they are on stock again.

A good product!!! This comes pre-programmed. But the PID values are all out of boundaries. So you will face a hard time setting it up...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

A good product!!! This comes pre-programmed. But the PID values are all out of boundaries. So you will face a hard time setting it up...

bu gne kadar kullandm kartlar arasnda en iyisi.
gps modl de almanz tavsiye ederim.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

bu gne kadar kullandm kartlar arasnda en iyisi.
gps modl de almanz tavsiye ederim.

The ever expandable MultiWii controller

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The ever expandable MultiWii controller

The 0.03 hectopascal maximum resolution of the BMP085 is an optimum enabling the sensor to respond to differences in altitude of 25 cm.



At this days pressure sensors have ~ 10cm. altitude sensitivity!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The 0.03 hectopascal maximum resolution of the BMP085 is an optimum enabling the sensor to respond to differences in altitude of 25 cm.



At this days pressure sensors have ~ 10cm. altitude sensitivity!

  1. 1
  2. 2
pin assignments Download [184]
No File Name Download [184]
Newbies Guide (By ATXHELI rev. 04/22/201 Download [452]
pin assignments with Batt monitor resist Download [199]
Flight-Ctrl ME 2.0 Schematic Download [781]

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!