New Items 论坛
注册

Total Price

AU$ 0.00

购物车 0 购物车 0 Loading...

MXS-R特技飞行3D巴尔萨20CC1625毫米(ARF)

MXS-R特技飞行3D巴尔萨20CC1625毫米(ARF)

Discontinued Product

Please continue searching for a similar product.
重量:
7500
SKU:
248000004-0
WANT FREE SHIPPING? Click here to find out more!

其中一个最热门的期待特技飞机周围是MXS-R。美貌是不够的,在Hobbyking MXS-R 20CC在设计时考虑到,真棒和极端的特技飞行表演的一件事。

在MXS-R 20CC的质量仅仅是尽善尽美,机身已建成,以保持飞行重量最小的,但强大到足以采取极端的特技飞行的处罚。精湛的品质覆盖已熟练应用,为最后的触摸,整流罩,树冠和车轮裤子都处于深光泽涂料成品。其中包括轮毂,油箱和碳纤维控制角的硬件非常好,也选择了继续飞行的重量降到最低。此外,该机型的特点插上翅膀和碳纤维起落架和尾轮总成。

该HobbyKing MXS-R 20CC执行地地道道看起来那么好,自然它使一个伟大的运动特技飞行,但它是公平地说,真正的3D是什么MXS-R已被设计为。轻量级和机身,大的控制面的精确度,令人惊叹的外观和顶线质量规范使MXS-R 20CC一个必须有平面所有特技和3D的飞行员!

特征:
•几乎箭在弦上 - 只需安装电机,电池和电子产品的选择
•所有的轻木和胶合板建筑
•碳纤维起落架和尾轮总成
•两片插上翅膀
•应用雄伟,高品质的覆盖
•全翼型水平尾翼/电梯/尾翼和方向舵
•易于定位优异的配色方案
•大型机身舱口
•可选翼尖侧向力发电机

眼镜:
翼展:1625毫米
长度:1500毫米
机翼面积:50.1dm2
空重:2700克

要求:
20CC汽油发动机
6准则性高扭矩伺服
5-6通道发射机和接收机
接收器电池
其它胶粘剂

  • SKU 248000004-0
  • Brand Other
  • 重量(g) 7500.00
  • 长度 1230.00
  • 295.00
  • 高度 470.00
  • IC / 2 : ELEC -
  • Motorsize (直径或 - cc)的 -
  • 翼展(毫米) 1625.00
  • Length(mm) -
  • SaleWeight (G) -
  • 容量(mAh) -
  • 20cc MXSR

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

This is a very well made airplane.
This MXS-R is also made under brandnames like Aerobeez and/or Flight Models.
The airplane looks a lot like Extreme Flight, only this one is a little bit heavier.
The airframes weight is just above 2 KG (this is without electronics/motor).
I have converted mine to electric. My setup is: TurnigySK3-5055/430kv motor, and 100 A esc with BEC.
Lipo battery is 3700Mah 6S. APC 16x10 propellor. Total weight just under 3200 grams.
I haven't flown it yet, but expectations are high.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This is a very well made airplane.
This MXS-R is also made under brandnames like Aerobeez and/or Flight Models.
The airplane looks a lot like Extreme Flight, only this one is a little bit heavier.
The airframes weight is just above 2 KG (this is without electronics/motor).
I have converted mine to electric. My setup is: TurnigySK3-5055/430kv motor, and 100 A esc with BEC.
Lipo battery is 3700Mah 6S. APC 16x10 propellor. Total weight just under 3200 grams.
I haven't flown it yet, but expectations are high.

Hi everyone,

I highly recommend this kit, it is a top quality ARF with strong hardware. I had to reorder due to my learning curve in gas engines. Installed an OS GT-22 with rubber mounting (Dubro) and it is a great choice. Used recommended servos but make sure you put a strong receiver battery (ideally the most powerful 2S lipo suggested).

I'm still in the break-in period with the motor so not completely sure but I'd say this is not a pure 3D model, more a Sport flying but I will try to move weight and maybe use a smaller gas thank. Other than that go ahead and order it for such a low price!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Hi everyone,

I highly recommend this kit, it is a top quality ARF with strong hardware. I had to reorder due to my learning curve in gas engines. Installed an OS GT-22 with rubber mounting (Dubro) and it is a great choice. Used recommended servos but make sure you put a strong receiver battery (ideally the most powerful 2S lipo suggested).

I'm still in the break-in period with the motor so not completely sure but I'd say this is not a pure 3D model, more a Sport flying but I will try to move weight and maybe use a smaller gas thank. Other than that go ahead and order it for such a low price!

Update now that the MXS-R is built.
Hardware spec (electric conversion) is:

Motor: Turnigy SK3 5055 430kV
ESC: Yep 120A c/w 10A SBEC
Battery: 6s, 5000mAh, 40c
Prop: Zoar/JXF 18x8 wood
Servos: 'Goteck' HV Std size Coreless

It all went together perfectly. I used 75mm standoffs to position the motor. The dual elevator servos needed 2mm packers to stop them hitting each other. balance was spot on.
She flies great, ample power and needed virtually no trim. the wheel pants cracked a little due to longish grass but that's a general problem with wheel pants when flying off grass. Handling is great, very little coupling and good post stall handing, no wing rock to speak of. Highly recommended.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Update now that the MXS-R is built.
Hardware spec (electric conversion) is:

Motor: Turnigy SK3 5055 430kV
ESC: Yep 120A c/w 10A SBEC
Battery: 6s, 5000mAh, 40c
Prop: Zoar/JXF 18x8 wood
Servos: 'Goteck' HV Std size Coreless

It all went together perfectly. I used 75mm standoffs to position the motor. The dual elevator servos needed 2mm packers to stop them hitting each other. balance was spot on.
She flies great, ample power and needed virtually no trim. the wheel pants cracked a little due to longish grass but that's a general problem with wheel pants when flying off grass. Handling is great, very little coupling and good post stall handing, no wing rock to speak of. Highly recommended.

Top quality kit, rivaling the liked of Extremeflight. This is the exact same airplane that you can buy elsewhere for double the price from the likes of Aerobeez and others.
Quality of the airframe and components really are top notch. The only slight criticism I can level at it is the paint on the canopy does not match the covering very well but that's not a big deal.
One thing to watch when choosing servos: Servo cutouts are for standard size servos, but infill plates for mini servos are supplied. The dual elevator servos ideally need to be quite low profile to avoid them hitting each other. About 22mm from bottom of servo case to mounting tab, max.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Top quality kit, rivaling the liked of Extremeflight. This is the exact same airplane that you can buy elsewhere for double the price from the likes of Aerobeez and others.
Quality of the airframe and components really are top notch. The only slight criticism I can level at it is the paint on the canopy does not match the covering very well but that's not a big deal.
One thing to watch when choosing servos: Servo cutouts are for standard size servos, but infill plates for mini servos are supplied. The dual elevator servos ideally need to be quite low profile to avoid them hitting each other. About 22mm from bottom of servo case to mounting tab, max.

Wow! What a great flying plane and at such a great price. One of the best looking and best flying planes you can have. I have had many including 3d HobbyShop and this compares to it. Does anything you want and can just Elevator it down to the runway. Check around and you will see Hobbyking has it 100-200 dollars cheaper than other sites. This is a "Flight models" model. I have the green one and know bought this one.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Wow! What a great flying plane and at such a great price. One of the best looking and best flying planes you can have. I have had many including 3d HobbyShop and this compares to it. Does anything you want and can just Elevator it down to the runway. Check around and you will see Hobbyking has it 100-200 dollars cheaper than other sites. This is a "Flight models" model. I have the green one and know bought this one.

Just want to start by saying, what a great quality kit. All the hardware is top quality with carbon fibre horns and ball joints. Everything fitted together well with a few small adjustments here and there. Being my first balsa kit it was still quite straight forward to put together. The supplied CD contains a basic manual that is some help but leaves a fair bit to the imagination.

I set my plane up as ep with an ntm 5060 380kv motor, yep 100amp esc, 4500mah 6s batt, 18x10 wood prop and towerpro mg996r servos . All that was needed to make it ep was a hk adjustable motor mount.

The only problems with the build being the 2 elevator servos hit together inside the fuse as it get very narrow towards the tail. I fixed this by putting a small block of wood on one side of servo as a spacer. Also a similar problem with the control horns in the rudder touch as you push them though either side so can't go all the way in but I just evened them out and glued them and they seem solid.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Just want to start by saying, what a great quality kit. All the hardware is top quality with carbon fibre horns and ball joints. Everything fitted together well with a few small adjustments here and there. Being my first balsa kit it was still quite straight forward to put together. The supplied CD contains a basic manual that is some help but leaves a fair bit to the imagination.

I set my plane up as ep with an ntm 5060 380kv motor, yep 100amp esc, 4500mah 6s batt, 18x10 wood prop and towerpro mg996r servos . All that was needed to make it ep was a hk adjustable motor mount.

The only problems with the build being the 2 elevator servos hit together inside the fuse as it get very narrow towards the tail. I fixed this by putting a small block of wood on one side of servo as a spacer. Also a similar problem with the control horns in the rudder touch as you push them though either side so can't go all the way in but I just evened them out and glued them and they seem solid.

No File Name Download [2792]
No File Name Download [2792]
No File Name Download [2077]
No File Name Download [2057]
No File Name Download [6461]
Manual MXS-R (English) Download [5784]

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save