注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global

光电气体杀死开关

光电气体杀死开关

QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 16.50
Rating:
Stock:
重量:
29
SKU:
GAS-SW

Price War

产品介绍

该设备可以让您安全,远程与变送器杀了你的电子点火发动机的装备。

规格。
输入电压:6〜12V
输入电流(最大):6A

 

注:说明书是文件标签下

Product
Specifications

额外信息

  • 商品编号:
    GAS-SW
  • Brand:
    N/A
  • 重量(g)
    29.00
  • 长度
    110.00
  • 宽:
    10.00
  • 高度:
    95.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I've just found that my switch will only kill the motor if I switch it on before my receiver is switched on. The motor will run all right. It just won't kill the motor. I don't know if every switch is the same, but just something to try if your's isn't working correctly. Works all right on a 4.8v 4cell flight pack.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Used to make kill switches using an Arduino board. But at this price I can not manufacture it myself
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Componente essenziale per staccare la corrente sui motori benzina,ottimo prodotto
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
G'day Got one before and it didn't work below 6V, Ran a regulator after the switch and job done. I got another one and hooked it up. Lights came on and wouldn't turn off. So I dived into the reviews here and found that the input/output wires were reversed on the board, confirmed by swapping I/O with a couple of adaptor leads. Resoldered the leads and bingo, works well now.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Ordered two of these and they arrived today. Mine arrived with the in and out connectors soldered in the correct sense i.e. the input has a socket on it to accept the plug on the battery pack and the output has a plug on it. They also work correctly down to 3.6 volts on the load power supply so the ones I have will work as a ignition on/off switch when using a 4.8 volt pack to power the ignition on a gas engine. The fail safe works in that it will cut the power to the engine ignition box if the Tx /Rx link fails. Top marks HobbyKing!!!!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Ideal en caso de que se rompa el mando de acelerador, o se trabe el carburador, o el ralenti del mtoor sea tan bajo que no se pueda plantar. Esto corta la chispa del cdi y apaga el mtoor. RECOMENDABLE
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Does the job perfectly
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very good, no problems with interference, using with a dle 20cc, good to kill engine right before landing
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Great little item, to be used on my 30,5ccm Baja
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Very nice little unit, does exactly what it says it will. Note 6v is NOT required. It works fine with 4.8v on both sides.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。