所有新的Quanum Q-3D是专为350〜500大小的多旋翼模型的GoPro英雄3和Quanum FPV +摄像机（如Quanum新星，侦察员X400采用了高性能，3轴无刷摄像头万向节大里H500，QR X350 PRO和DJI幻影）。
在Q-3D是市场上的最小和最轻的3轴无刷平衡环中的一个。在刚刚110毫米高，它可以清除大部分多旋翼飞行器起落橇和仅重185克，非常适合350〜500大小的多旋翼飞行器。两个倾斜和滚动可以在从一个R / C通道即时地调整，并具有高达28伏的一个巨大的工作电压范围。
从工厂的Q-3D是预调谐，无需安装，只需到Quanum新星，侦察员X4，QR X350 PRO或DJI幻影底部螺栓，安装GoPro的英雄3 / Quanum FPV +摄像头和你准备拍摄专业稳定空中视频！
•适用于大多数350〜500大小的飞行器模型（直接适用于新星，侦察X4大里H500，QR X350 PRO和DJI幻影）
适用相机：iLook的/ iLook的+ / GoPro的系列/ Tunigy ActionCam
I want to be as honest as possible with this review. Overall, this gimbal was poorly designed from the start and has several issues.
It's designed to work with GoPro's and I have a Hero3. However, due to the placement of the camera, attaching a USB AV cable is difficult to say the least.
You cannot not control yaw via an RC channel, but I was aware of this when I bought it. It's a minor inconvenience for me, but a bigger problem is how if you want to control pitch via an RC channel, you must also use another channel for roll stabilization. You cannot control just pitch as the roll channel floats and then eventually drifts. That is a pain.
Third, if you plan to use a different camera or add a filter, you must change power and gain settings every time you power up. Apparently, my gimbal does not save settings after I set them. Unfortunately, you would hope there was an easy USB connector to adjust settings via your computer, but you must buy a proprietary adaptor to do so. Why do this at all?
Fourth, vibration isolation to prevent camera jello is sub-par. Decent experimentation is needed even on a fully balanced rig.
Overall, I cannot recommend this gimbal despite it's low price. It's finicky and just wasn't properly designed to "make sense".TENGAN MUCHO CUIDADO CON LA POLITICA DE PRECIOS DE LA MARCA HOBBYKING
HOY TIENEN UN PRECIO Y MAÑANA OTRO , ES INDICNANTE .
TENGAN MUCHO CUIDADO CON ESTOS SEÑORES , PARA MI SON UNOS INCONPETENTES!This product is purchased in order to use the camera for fpv.
There are a lot of expectations.I can't give a proper rating for this, since I haven't been able to properly test it. The gimbal is by Quanum and claims to be compatible with the Quanum Nova, but neither the screws that came with the Nova, nor the screws that came with the gimbal can be used to attach the gimbal to the quad copter.
The Nova has four threaded holes for camera mount in a cross pattern. The sideways pair is M3 and the lengthwise pair appears to be M2.5. So the M3 screws that came with the gimbal don't fit and the M2.5 screws that came with the Nova are too short.
quality is not that great but is very cheap!Great product for the money, I bought one of these after damaging an expensive zenmuse gimbal, this is easily 90pcnt just as good as a zenmuse. Easy to set up, I use with a Turnigy Action Cam HD without any issues.I was a bit disappointed because you cannot control yaw from the Tx, but it works pretty well. I did have to zip tie the white balls because they caused tons of vibration during flight.Very disappointed with this gear. 1) Although advertised as ideal for the Quanum Nova, it is in fact it is too tall. It will touch the ground if you don't install some extra pads to the landing gear. 2) It points some degrees to the right all the time. 3) The pitch and roll potentiometers have no effect. 4) It does not center in accordance with the transmitter knobs. 5) It is not possible to limit the yaw stabilization, so will be looking at the Nova landing gear every time you make a turn. 6) The instructions manual is an absolute disaster. HK should hire English native speakers to review their manuals before releasing the product. I do not recommend this to be installed on the Quanum Nova quadcopter.
Going to it's travel limits my Q-3D is starting to behave very strange but in normal working conditions it just works great!to mount it in quanum nova it requires 2 M3X8 bolts that are not included. the motors seem to be little weak.
manual download now [2915kb] CX20 Wiring for Q3D download now [4846kb] No File Name download now [1783kb] No File Name download now [1214kb] Wiring for CX20 download now [1783kb] Wiring for CX20 download now [1783kb]