注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global

SK450死猫“除颤”电源和A / V配电板和电源盾

SK450死猫“除颤”电源和A / V配电板和电源盾

QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 33.11
Rating:
Stock:
重量:
463
SKU:
9171000236

Price War

产品介绍

我们拿出除颤器,并到死猫转换震惊一些严重的生命!蜘蛛风格的四直升机已经真棒与螺旋桨免费FPV鉴于其优化的ARM角度和布局。现在期待已久的发展向综合功率和A / V配电板,并插入屏蔽的功率。

新的较低板有电机ESC电源线直接焊盘就在武器和权力“,在”直接位于电池上面,以尽量减少布线垫的基础。有电源连接器的前部,背部和您的FPV齿轮和飞行控制器中间,所有连接到电源屏蔽哪些费力提供一个调节,过滤,射频噪声在一个更有3安培的照相机和飞行控制器屏蔽5伏和1放大器12伏的饥饿视频发射器。在前面和后面的视频连接器也不仅供应电压,但也带来了前置摄像头到后安装影像发送的音频和视频信号。此次升级将节省您的体重,清理你的布局,并通过减少连接故障提高可靠性。我想这死猫具有毕竟九条命!

特征:
•集成配电
•威克风格焊盘
•照相机和视频传输综合布线
•3或4个单元格中输入
•SMPS射频噪声保护屏蔽器
•热保护

眼镜:
输入电压:8-16v(3-4单元lipoly)
重量:142克
输出:5V / 3A和12V / 1A

*注死猫除颤器转换为SK450需要Sk450框架和死猫转换下面有关。

Product
Specifications

额外信息

  • 商品编号:
    9171000236
  • Brand:
    N/A
  • 重量(g)
    463.00
  • 长度
    375.00
  • 宽:
    30.00
  • 高度:
    215.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I am completely happy with this, what a great product! This did wonders to clean my quad up! Some sort of schematic would have been nice however a quick check with my DVOM and I was off and running! This is a must have for the Deadcat frame!!!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
great thing, saves a lot of cables

and makes it look cleaner
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is a must for your dead cat upgrade

making the whole upgrade look the bees knees
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Fairly straightforward but I wish it came with documentation on what each connector does.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I was hoping this board would make the addition of a camera and Vtx easy and quick. Not so.

The connectors on the board are male 4 contact connections. It is very difficult to find female 4 contact connectors. I tried using 3 conductor female servo connectors without the outer sleeve. When installed there is not enough room for these connectors on the controller and battery connector and the connector will hit the top board.

The best solution is to remove all of these connectors and install header pins. Once this is done standard male servo connectors can be used. The 4th pin is for audio, which I did not use so the 3 pin connectors would work.

Somewhat disappointed as this created a lot more work than should have been necessary.

If the board would have had header pins. I would give 5 stars.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
this is a great idea, too bad it will be useless if they ban fpv
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
So a friend and I are building dead cats. His is built and flying and after a hard landing the copper band for his ground circuit going to the defibrillator cracked and started pealing off. My frame hasn't been build because my filtered 12v to my video TX is shorted to ground out of the box. .......Not to mention his was nose heavy with a go pro 3 and a 3300mah 3 cell. So I ordered a 4000mah 3 cell because I have a heavier go pro 2 and ccd board cam for fpv but then ran into my electrical short when pinning out the board. I had high hopes for the dead cat but am having second thoughts now for sure.
Cheap lower defibrillator board.
Nose heave with a go pro sized camera. (With 3300mah)
Arms flex

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I had bigger hopes for this. You have 5V in the front and 12V in the back and a just one extra pin intended for video between front and back. I would like to see both 5V and 12V front and back and some extra pins that I could use for whatever.



The defibrillator seems to output 10V on the 12V pin based on just a quick test with 3S.



Also note that the pins are FEMALE for everything. If they where male we could use the extra servo cables we have...



Connecting a Tarot 2D gimbal to this needs hacking. The defibrillator is in the way and the provided holes are not suitable for the Tarot. I opted to add a separate plate in between the deadcat and gimbal.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Totally agree, the idea is good, like the Black Sheep TBS Discovery product, but the difference is they give you hook-up pins and connectors. HK, at least give us a reference or source to find the pins we need. Come on HK, you have a good concept, follow it through and give your customers a complete product.......after all you require us to buy three different kits to get "one".
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
  • Dead Cat PCB Board

Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。