TURNIGY AerodriveXp SK系列AerodriveXP SK系列电机是专为那些谁想要的外转子技术最好的为他们的R / C飞机。通常约8-10％的效率提高，可以看到在类似的入级电机。这是由于以下的部分;定子叠片：0.2毫米型号：SK35-36 910
KV：910rpm / V
建议螺旋桨：10 * 7,11 * 8.5 12 * 5
*包括安装和道具适配器附件（未显示）结果是英寸SK电动机摇滚！第三方测试结果表明，该电机具有903rpm / V一千伏及以下数据;
I / O：1.11A
测试结果还表明这种电机有作为，如果比好蝎子3014-18 / 3014-22或Dualsky XM3536CA-8性能不是更好！
Unit Weight (g):
Der Motor luft mit 4S sehr gut, mit 3S hat er "Startschwierigkeiten" d.H. luft nicht sauber an, sondern stottert fr mehrere sekunden. Ideal fr Scale Flugzeug um Motorstart eines Verbrenners zu simulieren... nein einfach mhsam. Die Welle ist viel zu weich. Gehrteter Stahl wre ideal. Wann lernt Hobbyking mal, dass weicher Stahl fr Motorwellen ungeeignet ist??
Power und laufruhe sind tiptop.I have been very impressed with the specimen I got of this motor. Even though many have had bearing problems on this and similar motors, my 910kv motor really is superb. Test data as follows:
4s, 1000 25C Turnigy Nanotec (only had 2x 2S 1000 packs, 4s 2200 45C's on order now :D ), 11x5.5E APC, 40A Hobbywing ESC (same as Turnigy Plush) excellent match. Voltage dropped to 14 from over 16 - this will be much better on the 2200's. RPM was 10500, Amp draw 23.9. This means 335W, which will give me about 200W/kg, gr8 for 3D flying, and it will be more on the 2200 45C's. Motor was cool after 1 min run. This is going to be a perfect match for my e-Flite Pitts... a solid 5 stars.
"This is an archived page. This product is no longer available and has been replaced by a newer product."
One of the very best motors HK has offered and now it's gone???
Bad move, HK. This motor can be used with 4-cell batteries, and the NTM Propdrive "replacement" can't. What kind of "replacement" is that?I fly with this motor for a month, with a 11*7 prop, and on 3s lipo.
I use it for FPV and need a motor i can trust-It gives a lot of power to my 2,3 kilo homemade model.
But sadly today i stops in mid air-I was lucky enogh to get my plane home in 1 peace-But the motor was burnt inside.I used 3536-900 in a BF109 Messerschmitt Foami ( LN Models )
- Total Weight = 850g
- Lippo = Turnigy Nano 2200 3s
- Propeler = 9x6, 10x6, 11x6
- Controller = 30A (hot) changed to 40A
Very good acceleration, i can fly with only 30 Throttle, very low consumtion 130mah, i fly about 12 minutes.
My first 30A Controller got hot, so i changed to 40A, much better now.
As others said, the bearings are a little bit noisy, but don't worry or replace them, you need two of them:
- ball bearing = 4x9x4mm called 848zz
- ball bearing = 4x12x4mm called 804zz
Hola, monte 8 motores de estos en mi oktokoptero, excelentes no se calientan, llevo lipo 4S helices 10x4.7 trabajan bastante descansados. excelente respuesta a la aceleracion. Los recomiendo.great little motor for the dollars. I don't stress it at all 3S, 13x4 23a.
be aware motor not supplied with 4mm prop adaptor (been on backorder for weeks) and the shaft will bend if you have a ding so order one while your at it (also been on backorder for weeks)
Tres bon moteur, belle finitionAbsolute Crap, didnt last 60sec's testing, pulling 280watts on a 3S, 14x4.7 prop, nothing but smoke....just as well I tested otherwise my octocopter(yes i brought 8 of these...) would of gone bye bye!
Avoid these like a kick in the nutz!
:(5 star for a very good motor/price report. I bought a total of 6 along time, each and every one runs very fine today, after aprox 10 months since the first test. 4 of them were for a quadrocopter which flew well, then I use'em in a variety of planes, single or pairs (bimotor), on big planes with 4S battery, or small planes, etc.
I don't know if something it's changed now in production line and quality or I just was plain lucky in the first time, but I recomand it!!!