该Turnigy 2合1电力仪表/伺服仪表是在你的飞行箱一个伟大的工具。它可以快速，方便地测量电压，电流和几乎所有的R / C电子元件的功率。
通道1是专为伺服使用，可处理高达8.4V / 10A。酒店拥有JR型插头连接，让您可以轻松地直接连接你的舵机仪表。这是用于确定您的ESC的BEC可以处理模型的伺服系统十分有用。
通道2功能12AWG输入/输出引线和高达60V / 100A支持。这是完美的，你检查电力系统在任何从微观到大型电动模型！
•2通道操作（CH1 8.4V / 10A最大，CH2 60V / 100A最大值）
伺服仪输入CH1：8.4V / 10A最大
功率计输入CH2：60V / 100A最大
Warning : Color code for servo lead :
<a href='http://www.hobbyking.com/hobbycity/store/uploads/504377516X1071262X43.JPG' target=_blank>SpareColorCable</a>
Otherwise it works great. Like it.
Screen graphs is cool but useless.Very nice.Works as expected.It for sure makes it a lot easier to set up your power system for max power..It would be nicer if it came with connectors already attached to it with addional connectors for different setup types.good to test servo max amp to help select bec.
and could help to select battery and escWas apprehensive abt getting these. But very nice product with a flashy colour display and a peak graph displayReceived mine a few weeks ago and tested it on a few motors and servos, can't say anything reliable about the accurary because I don't have anything to compare with, but I think it's accurate, all values it measured are ok.
The Screen with its different options is very nice, also the diagrams are nice to have.
All in all, for this price a great product and, if you don't have anything similar yet, a must have!
BUT: It doesn't come with any connectors, you have to order and solder them by yourself, no problem but you have to knwo it.This is a nice meter. I am using it in conjunction with the 7 in 1 battery meter servo function. But wait, before you can use it you need to correct the Futaba cable supplied with it. The cable has the white signal and the black negative pins swapped. Use an Xacto to lift the tab holding the pins in the J-connector and the white signal pin should be next to the J tab. Notice inn the photo above the cable shown is also in correct!meter works great, shows stuff in real time. everythinmg seeems to be working well, HOWEVER it will not work below 8V! so if you have anythign that runs on 2S and want to check out it's max amp draw u're out of luck. it'll keep flashing warning. great meter otherwise!Super usefull gadget, u can display many values and can see amps in time and consumption in mAh.Gute Anzeige fr die Ermittlung 2 verschiedener Stromkreise.
So ist der antriebsakku und auch im anderen Kreis der Stromverbrauch des Empfnger inkl servo ersichtlich.I have modified this meter in order to meausure power source with lower than 8V.
The power for the MCU is obtained by TL431 and NPN boost transistor and the regulated output voltage is 3.3V. Power consumption is 33mA @ 15V.
I added one 1A silicon diode to the cathode of existing diode (code 4A) on PCB. Plus( ) input of auxialiary power is supplied through the additional diode and negative(-) input is connected to negative(ground) pattern of PCB.
Howebver remember that always warning message appears on LCD when you measure power source with lower than 8.0V.
This is because you cannot set the minimum warning value at lower than 8.0V which is programmed in MCU and you cannot change this value.
Turnigy 2 in 1 Power/Servo Meter User Ma download now [1760kb] Instruction Sheet download now [1242kb] wiring OK download now [159kb] Additional cooler 2 download now [313kb] Additional cooler 3 download now [387kb] Additional cooler 4 download now [310kb] Additional cooler 1 download now [315kb]