注册

Product Finder

设置

Useful links

Live Chat
 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • USA

Turnigy电子驱动4020/08

Turnigy电子驱动4020/08

Discontinued Product

Please continue searching for a similar product.
Rating:
Stock:
OUT OF STOCK
重量:
279
SKU:
e-drive-4020/08
产品介绍

Turnigy电子驱动4020/08

规格。
号电池:4〜7×
锂聚合物
RPM / V:520
最大。目前的效率:20-40 A(> 78%)
空载电流:/ 2.1
电流容量:45A / 60
尺寸:40x20毫米
轴直径为 6mm
重量:253
推荐型号重量:2000〜4450
推荐道具无齿轮箱:13“-15”

Recomended设置。
与5S 14x7薄道具这给4250克推力。

平面型。
师:高达4500克
3D:高达2600g
运动/航空/ Warbird:3600克
EQ:0.54 IC发光引擎



所有电机螺旋桨包括适配器,连接器和安装附件。

Product
Specifications

额外信息

  • 商品编号:
    e-drive-4020/08
  • Brand:
    N/A
  • 重量(g)
    279.00
  • 长度
    0.00
  • 宽:
    0.00
  • 高度:
    0.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Gran motor... potencia enorme!! Excelente versatilidad x precio...

Buena compra.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Specs say it brings 520 RPM/V, with 5S battery I barely get 7.000 RPM W/14-7 APC type prop, very poor, hardly pushes my 1,9 kg plane, Im quite dissapointed, because I thought that with a 5S lipo I would do 3D ......
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
with a 14-7 APC type, and 4S hardly pushes 2Kg, I will order 5S batt, and bigger prop to make tests, and publish my results.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I have run this motor on my Piper Cub 2.08 Ws. 4.8kg. for many many houers now...Exelent motor..Have 5000Mah 5 cell and 15x8 prop...
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
un motor muy robusto y de poco consumo, estoy muy contento del resultado en mi 3d de dos kilos, un saludo desde espaa
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Motor de alta perfornance e rendimento, aconselho a todos que queiram fazer comverso de Motor Glow para eltrico, mas no se esquea de comprar tbem baterias com bastante MAh, pois o consumo alto tbem.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
The prop adapter covers a decent portion of the front air holes. My motor did get quite warm running at 40 Amps with a 5S setup.



Also the aluminum threads on the prop adapter shaft strip easily so don't over tighten.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
.....WARNING...

Front prop adapter that screws on with 4 screws only has a 6mm SHAFT!!! far too small, I fear it will snap if throttled up too quick, and the base it is machined up off is 32mm!! heaps of room from mounting screw recesses. UH please have larger shaft made(10mm minimum)!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I ordered two e drive 4020/06's and one e-drive 2215/20.

I got the 2215/20 just fine but the two 4020/06's were replaced with two 4020/08's instead, HobbyCity fixed the problem in less than a week! I decided to keep the motors sent and have them refund my 5S packs so I could order 6S instead to make up the lost Kv.



The e-drive motors seem well built. The case is solid and simple as you can see in the picture. You will have to take care when mounting not to block airflow to the holes.



I'm using a Turnigy Plush 80A ESC.



Here are the specs on my 4020/08.

At no load with 11.6V they drew 1.5 Amps and I measured 470.2RPM/V



NOTE: the following are for the 4020/08!

Shaft is 6mm diameter

Shaft collar with set screw is 16mm diamter

Bell collar is ~14mm

Threaded holes are 30mm apart on the side with the wires

Threaded holes are 23.5mm apart on the bell side (NOT 25mm)

Case is 50mm in diameter.

Case length is 42.5 of which the bell is about 31mm.





I rigged up a 6S setup with a 15x8 APC prop. This was too much prop because I was able to hit 40 Amps just a little after half throttle and my batteries were not even fully charged. Very very nice power.



I should be have some more props coming in and I'll post results of those as well.



The motor and esc got a little warm but my temporary mount was blocking some of the air flow to through the motor.



The only problem is I get a small glitch that feels like the ESC is missing a phase at very low throttle
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Master Airscrew 13 x 8 3blade prop

4S 23A 370 Watts

5S 32A 620 Watts



Master Airscrew 14 x 7 3 blade prop

4s 27A 450 watts

5S 37A 680 watts



Very poor hardware with this motor and casing is very thin.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。