注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global
  • USA

Turnigy全金属Servoless与退刀腿奥莱奥(三轮车,哈埠型)

Turnigy全金属Servoless与退刀腿奥莱奥(三轮车,哈埠型)

QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 67.45
Rating:
Stock:
重量:
276
SKU:
107000140

Price War

产品介绍

全金属Servoless与退刀鼻可转向大会和奥莱奥腿 - 高品质servoless收回系统模型重达3公斤,拥有全金属结构精度,可靠性和耐用性,还具有自动切断对电流过大的保护。包括的是一组质量奥莱奥腿和塑料轮泡沫轮胎。最后,空气和机械的可靠替代操作收回系统的机型!

非常适合哈布EDF

引脚尺寸:3毫米
车轮:24毫米
轮胎:45毫米
重量:58克每个(市电)60克(鼻单位)
最大型号重量:3kg
工作电压:4.8V〜6V

包括3路连接导线

Product
Specifications

额外信息

  • 商品编号:
    107000140
  • Brand:
    Turnigy
  • 重量(g)
    276.00
  • 长度
    170.00
  • 宽:
    60.00
  • 高度:
    90.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Bought these for my Habu 32 to replace eflites that bent with even the gentlest landing on grass. The mounting holes are identical to the fitted eflites but you will need to make up extensions to the oleos, otherwise not too much modification needed - just a bit of dremelling here and there.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Foam wheels and CHEAP plastic wheels. I performed about 45 seconds of low speed taxiing and the spokes on a main rim broke, and the front tire fell off and the front rim broke in half on decent asphalt. After upgrading wheels I had the struts repeatedly loosen I had to remove them and grind flat spots on the retracts, and drill and tap the M3 grub screws for M4. Only good on 70MM foam and smaller type A/C under 3.5 lbs I would say.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Works very well on Habu2
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Good value for the money. Workmanship seems good so far. Bench testing, all retracts are working. I put an obstruction in, and they stalled and stopped as they should. Then recovered on the next cycle. The biggest problem is these are NOT "ideally suited for the Habu". The struts are too short by an inch (25.4mm) or more. And the wire pin that holds the strut to the trunion is too thin to hold up. They are not as big a diameter as the stock eflite strut even. I will have to drill out the holes, install a longer, bigger dia pin to make the wheels reach the wheel well cavity. This is not beyond the skills of an experienced modeler, but the necessity to do this modification should have been in the product description. The other issue is the wheels barely fit at all in the wheel well. They will have to be sanded down. The CROWN rating isn't mine. HK seems to control this, so what's the point of having a rating. I give it 4 crowns overall, 5 for value, 5 for value, and a 3 for the incorrect description.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
retracts good. but I have two flights after one stopped working. where to find an electrical part?
motor - a whole, and the scheme does not work.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Nice and sturdy retracts, smooth and slow retracting actions. Built quality is very good as well. The main gear can be installed 90 degrees from the default orientation. Will be using it on my single 70mm F-22.

The measurement at the product description page is not very helpful so I did some measurement when the gear is extended.

From mounting plate to wheel axial:
Main Gear 75mm
Nose Gear 98mm
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。