注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global

Turnigy最小功率分配器(RED)

Turnigy最小功率分配器(RED)

QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 61.54
Rating:
Stock:
重量:
164
SKU:
373000002

Price War

产品介绍

Turnigy介绍适合的30cc加气动力的车型的最小功率经销商达盛电子(RED)。

本机具有强大的功能,其中包括:双电池输入,5V隔离线性RX BEC,每个通道上的双输出8路RX输入 - 简化了双伺服控制面。

大包裹体的独立5V线性稳压器提供接收器单独的电源,光电隔离CDI功率和内置远程点火杀。接收机,伺服及CDI功率源被彼此完全隔离。

(通过跳线)三种可选UBEC工作电压选项:

直接连接:使用5V〜6V的输入供电 - 电压电池输入传递到接收器
电压降0.5V:减少一个6V的输入至5.5V
电压降7805:使用7.2V- 8.4V输入来提供6V稳压电源


这是安全地窝配电'块'从而缩短电缆运行,将保护所有重要的接收器内的接收器超速成立时间第一电源分配器系统。

特征:
•5V可调RX BEC
•30安培伺服
•8(+1 CDI切)输入通道
•16个输出通道
•5状态检查指示灯
•软垫接收器托盘和安全的安装
•CDI隔离电源
•CDI遥控点火控制(遥控切)
•CDI电源状态指示灯
•CDI功率输出端
•CDI电压监控LED

可选:外部电源开关输入/输出电压显示

眼镜:
输入通道:8
输出通道:16
输入电压:5-8.4V
伺服电流:30A(40Amp连拍)
接收电压:5-8.4V(用户可调,默认为电压穿越)
工作温度:-20℃〜85℃
重量:80g
尺寸:116毫米点¯x88毫米点¯x13毫米

Product
Specifications

额外信息

  • 商品编号:
    373000002
  • Brand:
    Turnigy
  • 重量(g)
    164.00
  • 长度
    175.00
  • 宽:
    40.00
  • 高度:
    145.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Just want to say the tabs for the grommits are a bit weak on the new plastic housing and one has so far broken of on my 55cc plane, so in that respect I prefer the older version.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
WARNING! WARNING! WARNING!
The circuit diagram that comes with this product clearly shows 5v to servo's.
However upon using 2 X 3s lipo's for input voltage in became clear that the input battery voltage for main power is the same as the voltage that is outputted to servo's.
So if you use s3 11.1v for power this is the voltage that is output to the servo's
I found this out the hard way and ended up instantly burning out 5 X 70 Digital servo's
Total cost on burnt out servo's 350
The only 5v bec is to the receiver
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Purchased in early May/2015 so I can assume this is the latest version. There are conflicting specs between posted and instruction sheet however to clarify there is no internal rx voltage regulator. What you put in for voltage is what you will supply to the rx. Not an issue for me as I already own a good quality 20 amp BEC to be used with a 2S LiPo as the power source.
The buses are rated at 20 amps in the documentation supplied with the unit.
The internal CDI circuit worked as advertised and is a nice bonus at this price point.
One very good feature is the on/off switch. The unit is designed to turn on when the switch is open or simply not plugged into the unit at all. Should the switch fail in flight it will not turn your power supply off.
Over all I am satisfied this unit will be a solid performer for my 50cc gasser at a very good price point.
KR
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I have received the above pictured panel and it is a simple straight through power distribution panel, whatever power goes in the same comes out. (Three selectable UBEC operating voltage options (via Jumper): There is not a jumper wire to change the output voltage. The RX voltage is a constant 5 VDC. Hobby King has miss represented this item. I do believe the device will work fine but it is not as advertised.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I just got this red power distributor board and here is what I found. Knowing ahead of time this borad passes the power from the batteries striaght to the servo's I opted to use Life batteries. I am getting the 6.7v from the batteries power regulated to the reciever at 4.9v and I am getting 6.7v to all 8 servo's connectors on the board. I am only using a 7 channel reciever so I am using a servo extension on the board from the channel 8 position to supply 4.9v to the CDI power input of the board. That way I will not need an extra battery for my CDI cut switch. I than ran a servo extension from the position 9 on the board to channel 7 of my reciever so when I turn on channel 7 that turns on the CDI for my ignition and this setup works perfectly. I have it on a 82" Skyshark P-40 with a 50cc XYZ engine. Great value for the money
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I have 4 of these now and they work faultlessly, I use them for HV setups ie: 7.2v lipo in and 7.2v to servos and receiver, I even have one in a 35pcnt aerobatic plane.

As a pass through power box these are perfect. I would give 10 stars if I could.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Muito boa esta Powerbox, bem facil de entender as ligacoes, Nao utilizarei o kill switch dela, no mais parece ser muito bem feita.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Gesamtbewertung 10/2/2012

__hans

34 likes



ich habe 2stck davon.achtung nicht lipotauglich.Spannung auf servos mit 2s 6.6volt.cdi schaltung keine fuktion.ansonsten ok.

Hallo Hans, warum

bist du der Meinung es ist nicht Lipo tauglich ??? Mit 2S sollte es doch passen.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is merely a glorified power distribution bus.



It has a regulator for the receiver ONLY and direct passthrough for the servos.



You MUST use a battery that puts out what the servos can handle.

2S LiFe packs work best with this unit.



verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Doesn't work. Same trouple as the other guy. Voltage for servos is voltage of your power (in may cas 6.6v Life) 40$ for nothing. Thank's a lot HK for fake product.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。