注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global

Turnigy最小功率经销商UBEC(黄色)

Turnigy最小功率经销商UBEC(黄色)

QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 80.09
Rating:
Stock:
重量:
170
SKU:
373000003

Price War

产品介绍

Turnigy介绍适合的30cc加气动力的车型的最小功率经销商UBEC。

本机具有强大的功能,其中包括:双电池输入,5V隔离线性RX BEC,所有输出通道30安培电压可调UBEC,每个通道上的双输出8路RX输入 - 简化了双伺服控制面。

大包裹体的独立5V线性稳压器提供接收器单独的电源,光电隔离CDI功率和内置远程点火杀。接收机,伺服及CDI功率源被彼此完全隔离。

这是安全地窝配电'块'从而缩短电缆运行,将保护所有重要的接收器内的接收器超速成立时间第一电源分配器系统。

特征:
•5V线性BEC RX
•30安培伺服UBEC
•用户可调电压UBEC
•8(+1 CDI切)输入通道
•16个输出通道
•5状态检查指示灯
•软垫接收器托盘和安全的安装
•CDI隔离电源
•CDI遥控点火控制(遥控切)
•CDI电源状态指示灯
•CDI功率输出端
•CDI电压监控LED

可选:外部电源开关输入/输出电压显示

产品规格:
输入通道:8(+1 CDI剪切)
输出通道:16
输入电压:7-13V
伺服UBEC电流:30A(40Amp连拍)
输出电压:4.8-9.7V(用户可调;默认为5.2V)
RX功率:5V线性BEC
工作温度: - 20℃〜85℃
重量:80g
尺寸:116毫米点¯x88毫米点¯x13毫米

Product
Specifications

额外信息

  • 商品编号:
    373000003
  • Brand:
    Turnigy
  • 重量(g)
    170.00
  • 长度
    175.00
  • 宽:
    40.00
  • 高度:
    145.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

Quality
Value
Overall
Top, fr den Preis unschlagbar !!! Betreibe eine 3m Bella damit vllig Problemlos. Spannung einstellbar, Zndung ber die Weiche ein und ausschaltbar mehr geht nicht TOP !!!

Warte das sie wieder kommt, brauche noch 2 Stck davon....

Bitte HK schnell wieder auffllen !!! :-)
Quality
Value
Overall
Quality
Value
Overall
IT has not LCD SCREEN. IT HAS FAKE SCREEN. There is a Turnigy writing on the fake screen. Also a led is shining back side of the fake LCD. Another functions are ok. You can buy another version of this power distributor that it has almost the same functions from another stores cheaper than hobbyking.
Quality
Value
Overall
Quality
Value
Overall
Seemed to be a great product, all worked as it should initially, after three flights, CDI kill switch stopped working, red light flashes indicating less than 4.2V input no matter what battery is connected and the switch is inoperable.
Fitted on a Yak52 with a RCG 26cc gas engine.

I will now have to purchase a CDI kill switch.
Quality
Value
Overall
Quality
Value
Overall
Be careful to isolate this board from vibrations on the larger planes. My opto for the ignition control came loose from the board in my Sbach 34pcnt, 35cc, because I had the screws down too tight on the rubber grommet mounts. Bad solder joint. The ignition randomly shuts off (sometimes while in flight!). I'm going to isolate the board and receiver in foam and use Velcro to hold it in the plane. JohnnyB
Quality
Value
Overall
Quality
Value
Overall
I have purchased 3 of the original 3 panel design panel units. I have installed them into 3 of my giant scale planes. The new panels are a single plastic box. They are easy to use and they performed as intended.
CAUTION!! One of the 3 panel design units failed and I lost all power on my 84 P-51. What I found was one of the 2 ribbon solder joints fail on the main BEC that is located on the bottom panel failed. I was able to repair the remaining units by removing the top 2 panels and repairing the ribbon solder joints. Make sure to get the solder to flow to both sides of the panel. It was a simple repair but why should we have to repair them to ensure we dont lose our planes.
Come on Hobby King Pick up your game!!!!
PS I havent used the new design yet but I do hope they have resolved the problems.
Quality
Value
Overall
Quality
Value
Overall
This Bower box works Beautifully, But always remember to leave your assigned kill switch down when you turn on your transmitter and do this before powering up your Power Distributor, Then turn on the power distributor and your kill position will always be down to kill the CDI, This sequence is necessary unless you don't care where the kill position will be. This is a built in Safety feature to always start with the system in the kill position. Hope I made it clear to avoid confusion. Happy Flying ! Ron
Quality
Value
Overall
Quality
Value
Overall
Great product awesome price for this product. Only one thing could be made better.... an voltage display fr the bec adustment or an DIP Switch with steps and not an potentionmeter...
But again an awesome Product.
Quality
Value
Overall
Quality
Value
Overall
Muy buen producto... pero no es de 30A
Quality
Value
Overall
Quality
Value
Overall
Voltage to the servo will not change with the screw adjustment. It's stay the same as the default voltage 5.2 V.
Quality
Value
Overall
Quality
Value
Overall
I have it installed in my Raven, this thing works as advertised, the Opto Kill swiitch works really well. Just one little quirk, regardless of the servo direction you put the Opto Kill Switch onto, it defaults to the off position. Meaning, if you turn on the receiver regardless on the position of the switch on the transmitter, it defaults to off. Other than that little quirk, it's a great little unit. I have 2 X 2400 Mah 20C Lipo's hooked up to it, and the voltage regulator set to 6.0 volts. To adjust this, you'll need to turn in the potentiometer about 2.5 turns inwards. But the voltage is stable regardless of the state of the 3S Lipo. Receiver voltage is stable at 5:0Volts. Highly recommended.

Note, this is a rebranded RCCSKJ Power distribution board. The Yellow one is rated at 20 amps with peak of 30, that's a whole lot of amps for any size plane.
Quality
Value
Overall
View all reviews
Upload
Videos
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。