New Items 论坛
注册

Total Price

AU$ 0.00

购物车 0 购物车 0 Loading...

Turnigy Park250无刷先驱者2200kv

Turnigy Park250无刷先驱者2200kv

Shipped From:
  • USA
  • Global
QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 16.81
状态:
有货
重量:
55
SKU:
Park250-2200
WANT FREE SHIPPING? Click here to find out more!

专为3D parkflyers提供可靠和清洁的电力。 Turnigy EasyMatch Park250无刷外转子将提供更多的电源,并以其高效率,长的运行时间。
一个质量电机,专为设计有50瓦特无刷外转子飞的飞机建造。

规格。
电池:2细胞/7.4V
RPM:2200kv
最大电流:7A
空载电流:7.4V / 0.45A
电流容量:8A / 15秒
内阻:0.25欧姆
重量:14克(不包括连接器)
轴直径:2毫米
外形尺寸:35x23mm

需要;
10A ESC
2S对Li-Po / 6芯镍氢/镍镉
5.5x4.5〜8×6(SF)道具
适合的运动和规模的飞机重达6至12盎司(170克-340克)。

  • SKU Park250-2200
  • Brand Turnigy
  • 重量(g) 55.00
  • 长度 65.00
  • 40.00
  • 高度 40.00
  • 千伏(转/ v)的 2200.00
  • 最大电流( A) 7.00
  • 电阻( MH) 0.00
  • 最大电压(V) 7.00
  • 功率(W) 50.00
  • 轴(MM) 2.00
  • 长度B (毫米) 26.00
  • 直径C(毫米) 23.00
  • 可以长深(mm ) 14.00
  • 总长度E(毫米) 35.00

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Motor is ok. Simpler Brushless motor but is sufficient for my small park flyer. If you would like a better quality motor I would take a step up to a little bit more expensive Turnigy motor. Overall I have very good experiences with the Turnigy Brushless motors. The used Allen Keys are however 1 step too small from my opinion (1 mm).

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Motor is ok. Simpler Brushless motor but is sufficient for my small park flyer. If you would like a better quality motor I would take a step up to a little bit more expensive Turnigy motor. Overall I have very good experiences with the Turnigy Brushless motors. The used Allen Keys are however 1 step too small from my opinion (1 mm).

I chose this motor to match with my newly purchased Mini Crack Pitts Biplane. The motor that was recommended for this EPP shocky was too expensive, in my opinion. I've found that this Park250 motor works just fine without any problems at all. This is a fine motor as advertised.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I chose this motor to match with my newly purchased Mini Crack Pitts Biplane. The motor that was recommended for this EPP shocky was too expensive, in my opinion. I've found that this Park250 motor works just fine without any problems at all. This is a fine motor as advertised.

Runs like a champ on my scratch built, 3-channel twin tail-boom foamie trainer in a pusher configuration. Paired it with a HK Blue Series 12A ESC, Zippy 2S 800 & 1000mah packs, and a Gemfan 7x3.8SF trimmed down to 5.75" and the tips profiled like a stock one. That setup has more than enough power for a model with an AUW of 215 grams; I almost never go WOT, but it still stays pretty cool when I do!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Runs like a champ on my scratch built, 3-channel twin tail-boom foamie trainer in a pusher configuration. Paired it with a HK Blue Series 12A ESC, Zippy 2S 800 & 1000mah packs, and a Gemfan 7x3.8SF trimmed down to 5.75" and the tips profiled like a stock one. That setup has more than enough power for a model with an AUW of 215 grams; I almost never go WOT, but it still stays pretty cool when I do!

Very little high quality motor. Just be aware that to use (AFAIK) the Propadapter instead of the Prop Saver you have to push the Shaft trough (you can bend the shaft) or replace the shaft...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very little high quality motor. Just be aware that to use (AFAIK) the Propadapter instead of the Prop Saver you have to push the Shaft trough (you can bend the shaft) or replace the shaft...

These are quickly becoming my favourite motors. I have 2 of these on a park size cargo plane and it flies with ease. Also great for small scale warbirds.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

These are quickly becoming my favourite motors. I have 2 of these on a park size cargo plane and it flies with ease. Also great for small scale warbirds.

Grabbed this little motor for my Bonsai wing - right off the bat it was very difficult to mount properly. After managing to mount the thing the prop saver ended up being too small to be usable with any prop. Took a chunk out of the back of the wing from the prop wobbling around. Flipped it around and used it on my scratch build - on the maiden, it was more tail heavy than I expected, and backflipped, landing on the nose. This relatively slow drop from 2m managed to snap the shaft clean off. Oh well. I'd suggest grabbing the AX 2100kv motor for your Bonsai wing.
Anyway, if this motor is suitable for your uses - it does not come with pre soldered connectors. MAKE SURE you grab a 1.3mm hex wrench for the grub screws on the mount and supplied connectors, or you'll have a hard time getting it on your plane. The prop adapter is handy, but make sure the prop is spinning the opposite way of the thread, or it'll unscrew in flight.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Grabbed this little motor for my Bonsai wing - right off the bat it was very difficult to mount properly. After managing to mount the thing the prop saver ended up being too small to be usable with any prop. Took a chunk out of the back of the wing from the prop wobbling around. Flipped it around and used it on my scratch build - on the maiden, it was more tail heavy than I expected, and backflipped, landing on the nose. This relatively slow drop from 2m managed to snap the shaft clean off. Oh well. I'd suggest grabbing the AX 2100kv motor for your Bonsai wing.
Anyway, if this motor is suitable for your uses - it does not come with pre soldered connectors. MAKE SURE you grab a 1.3mm hex wrench for the grub screws on the mount and supplied connectors, or you'll have a hard time getting it on your plane. The prop adapter is handy, but make sure the prop is spinning the opposite way of the thread, or it'll unscrew in flight.

Unfortunately, I can't give this motor all 5's. As other reviewers have mentioned, unless it works for you as-is with the prop saver, buy another motor.

The hex wrench sizes for this motor are not supplied. They are microscopic to the point of being practically unobtainable. You need at least a 0.5mm - let me repeat, that's not 0.05" folks. It is a 0.5mm wrench that practically does not exist. It is not part of the standard DIN series of wrench/screw sizes.

Working past that problem by ignoring it, using the supplied prop adapter is virtually impossible. As other reviewers have stated, it is impossible to use the given shaft with the prop saver. I destroyed my motor just trying to remove the shaft - and I do this on other motors on a regular basis. Unfortunately, just a cheap knockoff. The bell housing is actually two pieces press fit together - the rim and the face. It came apart while extracting the shaft. I ended up with a fistful of broken parts. Oh, well.

Use this motor if you are ok with the prop saver setup. I will try to use the other of the two I bought from HK this way.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Unfortunately, I can't give this motor all 5's. As other reviewers have mentioned, unless it works for you as-is with the prop saver, buy another motor.

The hex wrench sizes for this motor are not supplied. They are microscopic to the point of being practically unobtainable. You need at least a 0.5mm - let me repeat, that's not 0.05" folks. It is a 0.5mm wrench that practically does not exist. It is not part of the standard DIN series of wrench/screw sizes.

Working past that problem by ignoring it, using the supplied prop adapter is virtually impossible. As other reviewers have stated, it is impossible to use the given shaft with the prop saver. I destroyed my motor just trying to remove the shaft - and I do this on other motors on a regular basis. Unfortunately, just a cheap knockoff. The bell housing is actually two pieces press fit together - the rim and the face. It came apart while extracting the shaft. I ended up with a fistful of broken parts. Oh, well.

Use this motor if you are ok with the prop saver setup. I will try to use the other of the two I bought from HK this way.

The Motor itself is great. I used it for a beginners microquad. With 3S and 5045 props it has plenty of thrust for a small quad. Motor gets only a little warm. The only serious downside is the included prop adapter. It is garbage. Do not use them as the shaft hole is highly eccentrical and the headless screw is way to weak to fix the adapter on the shaft while tightening the wingnut. That destroys the good pricepoint as you have to buy additional adapters.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The Motor itself is great. I used it for a beginners microquad. With 3S and 5045 props it has plenty of thrust for a small quad. Motor gets only a little warm. The only serious downside is the included prop adapter. It is garbage. Do not use them as the shaft hole is highly eccentrical and the headless screw is way to weak to fix the adapter on the shaft while tightening the wingnut. That destroys the good pricepoint as you have to buy additional adapters.

Un max de traction en 2S 300mA Nanotech et une 6x3 GWS pour un racer EIM.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Un max de traction en 2S 300mA Nanotech et une 6x3 GWS pour un racer EIM.

A real screamer. Used it for the Hobbyking Windragon and improved performace a lot without losing flight time. Also used in the mini stik balsa kit with good results.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

A real screamer. Used it for the Hobbyking Windragon and improved performace a lot without losing flight time. Also used in the mini stik balsa kit with good results.

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save