New Items 论坛
注册

Total Price

AU$ 0.00

购物车 0 购物车 0 Loading...

Turnigy Park300无刷先驱者1380kv

Turnigy Park300无刷先驱者1380kv

Shipped From:
  • USA
  • Global
QTY:

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 21.76
状态:
Backorder
重量:
73
SKU:
Park300-1380
WANT FREE SHIPPING? Click here to find out more!
专为3D parkflyers提供可靠和清洁的电力。这无刷外转子将提供更多的权力和与它的高效率,长运行时间。
一个质量电机,专为设计有77瓦特无刷外转子飞的飞机建造。

规格。
电池:2〜3节电池/7.4~11.1V
RPM:1380kv
最大电流:7A
空载电流:8V / 0.4A
电流容量:9A / 15秒
内阻:0.33欧姆
重量:24克(不包括连接器)
轴直径:3毫米
外形尺寸:37x28mm

需要;
10A ESC
2S〜3S对Li-Po / 6〜8芯镍氢/镍镉
8引脚6x5〜8x3.8道具
适合的运动和规模的飞机重达8到12盎司(225克-340克)。
  • SKU Park300-1380
  • Brand Turnigy
  • 重量(g) 73.00
  • 长度 65.00
  • 40.00
  • 高度 40.00
  • 千伏(转/ v)的 1380.00
  • 最大电流( A) 7.00
  • 电阻( MH) 0.00
  • 最大电压(V) 11.00
  • 功率(W) 77.00
  • 轴(MM) 3.00
  • 长度B (毫米) 25.00
  • 直径C(毫米) 28.00
  • 可以长深(mm ) 9.00
  • 总长度E(毫米) 37.00

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

This thing is a vicious little crap: just try to change the axle ( one spare provided... great!) the screws are glued so is the axle! (what tool for the screws? I tought I had about all of them....).
I never had a chance to run the motor for I was so mad that I hammered the dmn thing to death to the garbage!

Pierre. Engineer.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This thing is a vicious little crap: just try to change the axle ( one spare provided... great!) the screws are glued so is the axle! (what tool for the screws? I tought I had about all of them....).
I never had a chance to run the motor for I was so mad that I hammered the dmn thing to death to the garbage!

Pierre. Engineer.

I got this motor in a nice acrylic box which is basically useless. If HK invest packing cost into quality then we all can get better quality products. There was a label on the box saying 120W, but this is overrated, this motor can go safely upto 80 to 90W with 3S setup.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I got this motor in a nice acrylic box which is basically useless. If HK invest packing cost into quality then we all can get better quality products. There was a label on the box saying 120W, but this is overrated, this motor can go safely upto 80 to 90W with 3S setup.

I had a really hard time finding a prop that would fit on the prop saver. The prop saver is integrated in to the motor bell and is not removable. Since I couldn't find a propeller to fit the prop saver, I ended up trying to push the shaft forward to use the screw on adapter that is included, and is really nicely machined. I disassembled the motor, took out the pins and screws and on the first very light tap on the shaft the bell housing cracked and deformed, ruining the motor. I really don't like the design of the integrated prop saver and having the prop shaft run in to your airplane.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I had a really hard time finding a prop that would fit on the prop saver. The prop saver is integrated in to the motor bell and is not removable. Since I couldn't find a propeller to fit the prop saver, I ended up trying to push the shaft forward to use the screw on adapter that is included, and is really nicely machined. I disassembled the motor, took out the pins and screws and on the first very light tap on the shaft the bell housing cracked and deformed, ruining the motor. I really don't like the design of the integrated prop saver and having the prop shaft run in to your airplane.

Great little motor. plenty of power with a 8x4 propp on a foamy. Just to clarify - the axle CAN be pushed - BUT - you will need a vice, and the lockclamps are brittle and can break - and don't forget to remove the two screws that hold the shaft in place. Have done the procedure on two of these motors without problems. The only downside is that the shaft is fairly soft - and once bent will snap if you try to realign it - and there are no spares in EU warehouse. But still exellent varlue for money

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great little motor. plenty of power with a 8x4 propp on a foamy. Just to clarify - the axle CAN be pushed - BUT - you will need a vice, and the lockclamps are brittle and can break - and don't forget to remove the two screws that hold the shaft in place. Have done the procedure on two of these motors without problems. The only downside is that the shaft is fairly soft - and once bent will snap if you try to realign it - and there are no spares in EU warehouse. But still exellent varlue for money

This is an all around great motor. I use these motors on a quadcopter with an AUW of 620grams. The motors pull about 3.6A each at hover with plastic 8X4.8 props. The motors have an excellent amount of punch.

Be sure to check the motors carefully before using them. The motors use heat shrink tubing to protect the wires from rubbing against the housing. The heat shrink tubing on one motor was not properly shrunk and worked it's way out of the motor during flight.

Also be aware that there is no strain relief on the wires. Any vibrations on the wires will likely cause the wire to break at the windings. You must securely fasten the wires to prevent vibration. Apply some epoxy where the wires exit the motor housing or secure the wires close to the motor.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

This is an all around great motor. I use these motors on a quadcopter with an AUW of 620grams. The motors pull about 3.6A each at hover with plastic 8X4.8 props. The motors have an excellent amount of punch.

Be sure to check the motors carefully before using them. The motors use heat shrink tubing to protect the wires from rubbing against the housing. The heat shrink tubing on one motor was not properly shrunk and worked it's way out of the motor during flight.

Also be aware that there is no strain relief on the wires. Any vibrations on the wires will likely cause the wire to break at the windings. You must securely fasten the wires to prevent vibration. Apply some epoxy where the wires exit the motor housing or secure the wires close to the motor.

otimo motor forte e bom desenvoltura

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

otimo motor forte e bom desenvoltura

The motor construction looks very good and this motor comes recommended by the Flitetest guys for their scratch built system. However I have two issues.
1. The prop saver boss is 5.5mm diameter which is not a common size for propeller adapters. Certainly none of the props I've bought from Hobbyking have come with one.
2. I pressed the shaft through so I could use the supplied collet adapter There's a video about how to do this using a vice. Don't do it with a hammer! The collet was machined so out of true it wobbles half a millimetre back and forth when you spin it.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

The motor construction looks very good and this motor comes recommended by the Flitetest guys for their scratch built system. However I have two issues.
1. The prop saver boss is 5.5mm diameter which is not a common size for propeller adapters. Certainly none of the props I've bought from Hobbyking have come with one.
2. I pressed the shaft through so I could use the supplied collet adapter There's a video about how to do this using a vice. Don't do it with a hammer! The collet was machined so out of true it wobbles half a millimetre back and forth when you spin it.

I bought this to use on my tricopter, and after after a few flights everything works beautifully.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought this to use on my tricopter, and after after a few flights everything works beautifully.

Nice motor, not only for multicopters, but also for homemade foamies.
It performs great on my nutball for example.

However, I fail to change the default alloy prop saver.
I can not move the prop shaft either.
Both of them seems to be sealed to the motor...
If someone has a solution...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Nice motor, not only for multicopters, but also for homemade foamies.
It performs great on my nutball for example.

However, I fail to change the default alloy prop saver.
I can not move the prop shaft either.
Both of them seems to be sealed to the motor...
If someone has a solution...

I bought 4 of these motors to use on a small quadcopter but found that the propsaver is too large for any standard prop, as in the hole in the middle of the propeller is too small, also the screw provided didn't suit ANY metric or inch allen wrench.... so i had to spend more money buying philips head M2 screws... I didn't want to bore out all my props so i pushed the shafts through, note, this is a pain and i bent two of the 4, the shafts seem weak and the whole assembly despite using the most precise method i could, still managed to band the can so that not the shaft but the motor can is off center?!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought 4 of these motors to use on a small quadcopter but found that the propsaver is too large for any standard prop, as in the hole in the middle of the propeller is too small, also the screw provided didn't suit ANY metric or inch allen wrench.... so i had to spend more money buying philips head M2 screws... I didn't want to bore out all my props so i pushed the shafts through, note, this is a pain and i bent two of the 4, the shafts seem weak and the whole assembly despite using the most precise method i could, still managed to band the can so that not the shaft but the motor can is off center?!

  1. 1
  2. 2
  3. 3
  4. 4
Shaft diameter measurement Download [1353]
Turnigy Park300 1380kv & OrangeRx T-SIX Download [5898]

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save