注册

Product Finder

设置

Useful links

 
[["US","AU","GB","DE"]]
注册
Shipped From:
  • Global

Turnigy RotorStar双电源15A稳压器

Turnigy RotorStar双电源15A稳压器

Now save 保存 AU$ 0.00 AU$ 0.00

AU$ 69.81
缺货!
Rating:
Stock:
OUT OF STOCK
重量:
154
SKU:
9052000036

Price War

产品介绍

该RotorStar双电源15A电压调节器,可以直接向您的舵机提供稳定的电压和电流的双线性稳压器。这从接收器让你的连接更安全,更可靠的隔离伺服电源。随着高性能车型今天如0.90需要高功率伺服/ 700类直升机,在RotorStar调节时完美的组件供电。

目前,极端3D飞行变得越来越流行。其结果是,对于高性能伺服请求在不断增加。之一是影响伺服系统的性能,例如这些因素是能够提供稳定的,可靠的电力供应。该RotorStar调节可以通过使伺服到调节器的直接连接到CCPM伺服提供稳定的电力,也可以避免由于反向电动势外部噪声。

该器件还包​​括一个可选低电压报警/ LED板,可以很容易地提醒你你的输入电池低电压状态。它的特点是超高亮白光LED,可即使在阳光充足的条件可以看出。一个伟大的方式来监控您的RX电池的状态。

特征:
您舵机/接收器•稳定,可靠供电
•10A的连续/ 15A的最大电流伺服能力
•双输出功率为伺服系统和接收器
•可选的伺服输出电压5.2V / 6V / 6.8V / 7.4V / 8.4V
•可选低电压报警/ LED
•您RX电池容易重新充电集成充电通过领先

眼镜:
输入电压:2S Lipoly(6〜8.4V)
双输出:1。 RX电源5.2V 5A(10A最大)
2.伺服电源5.2V / 6V / 6.8V / 7.4V / 8.4V 10A(15A @ 6V最大值)
低电压报警:LIFE(6.5V),锂聚合物电池(7.3V)
开关类型: 故障安全(故障关于安全)引脚标志接触式
电源连接器:JST
外形尺寸:64×40 x17毫米
重量:59克

Product
Specifications

额外信息

  • 商品编号:
    9052000036
  • Brand:
    Turnigy
  • 重量(g)
    154.00
  • 长度
    144.00
  • 宽:
    36.00
  • 高度:
    110.00
Community
Discussions
Rate&
Review

撰写您自己的评测

Only registered users can write reviews. Please, sign in or sign up

Quality
Value
Overall
Unit defective. Could have caused a serious accident. Won't bother with an RMA because this only cost me $23.00. Weary of Rotor Star and Turnigy products, although the Turnigy servos i use have not failed yet. Spend your hard earned money on a Hobbywing 10A UBEC instead of this.
Quality
Value
Overall
Quality
Value
Overall
kaliteli rn tavsiye ederim..
Quality
Value
Overall
Quality
Value
Overall
I have this installed on my KDS 550, N680 HV servos on 6.8V setting and an Ebar plus AR6200 spectrum with satellite receiver and N690 on the 5.2v side. All seems OK but did burn out 2 N680HV with setup. The battery is a bit light for this unit but will upgrade it to higher discharge or just fit a few capacitors. Will post on further findings so far so good.
Quality
Value
Overall
Quality
Value
Overall
I have fitted this on my hk550tt fbl heli easy setup keeps my align servos at a steady 6v fitting the low voltage alarm/led is a must this can save your heli, fantastic product from hobbyking.
Quality
Value
Overall
Quality
Value
Overall
Hugh thing, that BEC, but as of now it works good. Feeded by a 3,3Ah nanotech lipo this a good powersupply for bigger helis.
Quality
Value
Overall
Quality
Value
Overall
Some days ago i received my unit , i tried it on my TREX 600 nitro modified.Trex 600Nitro flybarless Head Vstabi .Very nice Voltage regulator, non problem for overheat or electric jamming with the Vstabi or the receiver Futaba 2,4 Ghz. Really a good product.
Quality
Value
Overall
Quality
Value
Overall
Well what can I say... I have had a circa 6 flights (with plenty pitch pumping) with this and it seems great. Hopefully I am not speaking too early. On the work bench, if I do a lot of stick banging - pitch and tail, then the heat sink gets pretty hot! I hope this is not an issue. On the work bench there is no air flow, but then little resistance too. In the air you have the air flow to cool the heat sink and more resistance.

Now in fairness it only gets really hot when do plenty stick banging. Otherwise it remains just mildly warm when not going crazy on the tranny.

I am running a T-Rex 600N FBL 3 x DS610's and 1 x DS650 directly connected to the Rotorstar. Then connected to the receiver ports, is a Skookum SK540FBL with a DS620 connected to the Skookum for the throttle.

The pin flag works really well. I also have Spektrum telemetrics connected and it shows a steady 5.1v to the Skookum. I have not yet hooked it up to the servo ports as I need all four ports for the servos and no space for telemetrics.

All in all, this is great value for money compared to the GVR-7020. I just hope the quality is the same as the GVR-7020 and I don't lose my bird by by saving $60.
Quality
Value
Overall
Upload
Videos
  • Turnigy Rotorstar Dual Power Regulator

Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

产品标签

使用空格分隔标签。使用单引号(')标注词组。