你有没有安装伺服手臂，然后粘到位伺服，后来才发现手臂是一个或两个牙齿了吗？我知道你要说什么，“这是子修剪是为了什么”，或者你应该它插入接收第一，这意味着你必须找到一个电池，插上ESC，取出道具，拽出建立一个模型上的发射器，线材这一切，等好了那些日子已经结束了...该Turnigy伺服定心工具是有一个内置的锂聚合物电池，可以处理多达四个1520us类型或760us一个独立单元伺服系统，你只需插入你的伺服，按下电源按钮和BAM ...您的伺服去其中心，并在那里举行，让您安装在最佳位置伺服手臂，然后调整联动，集中一切。 30％的亚装饰和均匀偏转一边到另一边的日子已经过去了。凭借其内置的USB可充电电池，体积小巧，多功能伺服没有任何借口不建是正确的......从一开始。
I have had mine a little over a year now and really only used it to set up four airplanes. two days ago I broke it out to center up my new servos on my new eflite ultra stick, and the blue power light came on good and strong but when I plugged in any of the four servos, nothing happened. so I charged it to make sure it wasn't lacking any voltage, tried it again and still nothing. so now its just collecting dust. I messed with it a lot before I gave up on it. but it is dead in the water now. went back to the old way by powering up the plane and setting my controls. when it did work, it worked great. just doesn't seem to hold up for very long. like I said I only bought this about a year ago, and it only worked for 4 planes before it took a ****.excellent tool for centering the servos with no connections attached.
Small battery is installed so its ready to assist you. Really nice tool.This tool works exactly as advertized. You spin the arm any direction, then press the power button, and POW ... it goes right back to 1/2 way between the two ends. I tried it on the Turnigy 1250 GT first, over and over again ... it ALWAYS came back to center. I also have the black one, though I am not sure why I ordered both colors at different times ... and it works exactly the same. This is a great tool and makes it so easy to fine tune your centering the swing arm.excellent tool for centring the servos with no connections attacheddit ding is wel heel makkelijk in gebruik doet wat hij moet doen niet meer en niet minder, gewoon je servo in de middenstand zettenVery useful device, everyone needs the device.I bought this centering tool some time back,I replaced a couple of my servos yesterday and found it very useful,each servo was centered perfectly, a great little tool ,easy to use especially having its own power source.On 1520us setting this unit center the same as "Hobby King 2.4Ghz Receiver 6Ch V2" PRODUCT ID: HK-T6A-V2, "Turnigy 9X 2.4GHz 8Ch Receiver (V2)" PRODUCT ID: RX-9X8Cv2, "OrangeRx R615X Spektrum/JR DSM2/DSMX Compatible 6Ch 2.4GHz Receiver w/CPPM" PRODUCT ID: 9171000300-0 and "Turnigy Servo Tester" PRODUCT ID: TGY-ST. I have not tested the 760us setting for lack of compatible servos.With HXT900, HXT500, HobbyKing S036 Micro Servo, HobbyKing 3.7g Micro Servo and HobbyKing Windragon on 1520us the same result as my Turnigy Servo Tester, center every time, and even with repeated on/off cycles.simple to use the price is right