该Turnigy TY-P1 25Amp ESC是一个脱颖而出的表演。使用在美国开发的质量IR的HEXFET功率MOSFET，这是ESC处理超过40 Amps电流消耗电缆。然而，这在内部设计的ESC开发并通过HobbyKing工程团队在心中，质量和可靠性一个目标产生的。而不是通过率ESC和它推到一个更大的散热器的极限，因为很多公司做的，我们希望以设计为那些寻找一个防弹解决方案，速度控制器。我们采用SMT技术，而不是手工焊接产生一致的质量和可靠性每一次。该TY-P1 25A ESC还具有独立的稳压器（一个用于BEC，一个用于MCU）这确保MCU将在从BEC电路的高一时安培平局的情况下，保持供电，反之亦然。一个XT-60电池连接器和3.5mm子弹连接器已预先焊接方便。
制动（OFF / ON）。
love these ESC great for bigger planes like the Flite Test Guinea Pigcome da descrizione all'atto dellla vendita, molto soddisfattoVery good esc , easy card programming for multirotorThis is very good for my QuadGreat works perfectly with my ft Guinea pig and just like vid says this wax is meant to be 40 ampTought it was broken, but is didn't calibrate it... normally you don't have to wait so long to calibrate it but its ok. Actually these are pretty niceI actually have 17 of these in various multirotor aircraft that have worked perfectly for years now. They are reflashed with SimonK firmware. These were bought some time ago. I bought one recently that did burn out when setting up a FPV plane, I think it was a bad solder joint either on the esc or on one of the extensions I was using because the motor kicked back and forth when trying to power up and that's a sure sign of a bad connection.The moment I plugged this in it blew up.I can't recommend this product to anyone. Please avoid this product.
I had some test flights (5mins?) with my new quadcopter and these ESCs yesterday. After some KK2.1 parameter tuning today, I went to field to test new configuration. Right after plugging in the battery (Turnigy 2200mAh, 3S), I noticed some propeller movement, spark sounds from the esc AND SMOKE FROM THE ESC! Esc warmed a bit and is for sure broken.
Please note: the esc burned right after plugging in the battery. No throttle, no overload.
Now I am considering whether I should replace all my ESCs because if one burns like this, others may also. Next one might burn the flight controller and/or motors, if this one already didn't...
Bought 4 of these since they were suggested by HK for my quad project. I would not suggest getting these to use with the Multiwii board. After many, many hours of work 1 works all the time, 1 works sometimes, and 2 just beep. They all work fine connected directly to a Spektrum receiver. I don't think they communicate well with the multiwii.
Manual download now [89kb] Back TY-P1 Macro download now [304kb] Capacitors download now [2630kb] Capacitors download now [3339kb] pin-out-better download now [140kb] melted ground wire download now [121kb] 3 of 6 burn out of the box download now [1074kb] 3 of 6 burn out of the box download now [885kb] Manual download now [93kb] pin-board to flash without soldering download now [2659kb] TY-P1 flash pin out download now [84kb] Measure Length download now [270kb] Measure Width download now [269kb] microc2 download now [238kb] microc1 download now [291kb] 1 de 4 quemado al programar con tarjeta download now [167kb] 3 of 6 burn out of the box download now [2806kb]