Build the micro of your dreams with our new DSM2 compatible all in one receiver, ESC, and servo brick set. This tiny little unit is perfect for use for all your DIY micro projects. Use it to convert balsa stick and tissue planes to RC or whatever else you can dream up. The integrated brushed ESC means you can use any of the micro sized motors already offered by HobbyKing. This ESC is designed to use a 1S LiPoly setup, keeping weight to an absolute minimum. The two built in linear servos can be used to operate rudder and elevator, or depending on how you program it, elevator and aileron. Two additional servo outputs are included to plug in other servos when using the micro servo connectors.
Speaking of programming, this unit can handle a variety of airplane configurations from standard layout, V-tail, and delta wing options.
• Compatible with MTSS-A and DSM2 protocol, perfect for use with your OrangeRX T-Six transmitter
• 2 linear servos and integrated brushed ESC
• Supports fixed-wing, delta, and V-tail mixing
• 2 additional servo out connectors with 1.0mm plug
Protocol: MTSS-A and DSM2 Compatible
Servo Travel: 7mm
Torque: 35g @ 4.2V
Brushed ESC: 2A
Size: 24x24.2x8.4 mm
Weight: 3.4g (without power cord)
Operating Voltage: 3.7~5.0V
Plug: JST 1.0 Pitch ( Secondary inputs )
1) This is not a Spektrum DSM2 product, nor is it a copy of a Spektrum DSM2 product.
The Spektrum and DSM2 brand is a trademark of Horizon Hobbies USA.
2) This is not an underground black market fake Spektrum product. SuperMicro quality is guaranteed.
Hmotnost ( g )
I bought one of these as a replacement for my night vapour. While it is not a direct replacement with a couple of small dabs of hot glue it can be fitted and it works. There is even a socket to plug in the lights. Be careful soldering on the motor wires, the solder tabs are very close to the gears on the linear servos.
A lot cheaper than the Horizon Hobby replacement board.After a few seconds use the direction servo sticks in one position and won't move until the unit is re-powered, after which it sticks again. It's a shame because the other servo works fine and the programming functions are good (swapping sticks etc.). No good with one broken servo though, so I wouldn't buy another and risk the same thing again.So, here it is. Hooked it up into my broken NE P51, and have to tell, spendt an hour by soldering that micro tips, but here we go and action. Works excellent and i won't brake my mini again. Fast servo and throtle response, no signal los. So for it's prize, don't be worry.
Take tady to mme. Vtsnno do padlho NE P51, a musm ct, e jsem strvil hodinu pjenim na mikroplokch, ale deme dl. Funguje perfektn a dal havrie se tak nebude opakovat. Rychl reakce serv i otek, bez problm se ztrtou signlu. Za ty penze, se nen eho bt.Come on Hobby King , users need info ! or you wont sell certain tech products, get the manual on line .ASAP. lost sales and unhappy customers are the result.Hi 2 of these arrived today, smaller than the ar6400 The on board servos are elevator (right stick) and rudder (left stick), if you want them both on one stick you will have to use the TX mixes You have to solder wires to the PCB onto the very small holes, if the motor is reversed just swap them round (or put a small connector inline) Binding is a bit of a pain, although it follows the normal Spektrum method, RX on first (with a fully charged battery of course), you get the red flashing, switch on the TX with the bind button pressed and eventually it will go out then come on solid, that means its bound to the TX There may be other functions but without a manual its difficult HK WHERE IS THE MANUAL?, PLEASE COPY AND PUT IN FILES SECTION
Schottky BAT60A download now [242kb] FromRC_Groups download now [257kb] Brick elvon program added download now [183kb] motor wires soldered RIGHT download now [1126kb] No File Name download now [212kb] Change rudd-ail. download now [2.48Mb] orange and dsx-i download now [2.48Mb] orange and dsx-i download now [2.48Mb]