The E-Turbine FPV 250 is an exciting addition to our racing drone range. This fantastic model comes with a heavy duty carbon fiber frame, four TB2204 brushless motors, four 12A ESCs, a Camera and the CC3D Flight Controller. This is an ideal quad to get into FPV 250 quad racing with.
The high-intensity front LEDs will make night flying possible and the blue LED strap at the rear will help you and your competitors keep track of this fast-moving drone racer. The lights can be set for five types of flashes and have 8 levels of intensity.
Just add your own RC gear, video transmission system to connect to the included Sony 700 CCD camera and a battery pack and you are ready to race!!
Embrace your inner racer with the E-Turbine LED FPV 250 Drone Racer!
1x E-Turbine FPV Drone Racer
Weight: 408g (without battery)
ESC: 12 Amp
Camera: IC Sony CCD 700
Recommended Battery: Lipoly 3S 1500mAh (not included)
Required to complete:
Video Tx/Rx System
Hmotnost ( g )
Good quad no issues except the factory blades, changed and this quad care fly. no manual "that makes it Fun".Very good little FPV quadcopter! Very stable! But, buy together gemfan 5045 propeller, because the propellers that came in this kit is so poor and broke easyly.
CC3D extremaly easy to configure! Using Turnigy Nanotech 3S 1500mAh 35/70C I have a flight about 7 mins. I also installed a 450 helicopter landing gear (all white plastic) in this quad to prevent damage of forced landings. Turnigy ActionCam FullHD is who records my flights.Excellent little flyer! Was easy enough to build, but instructions would've been nice. Currently running it with default specs, using a 2200mah lipo. Works just fine, although you should adjust the D/R and throttle-curve for smooth flights. It can kinda carry a gopro, but it becomes a bit unstable and flys much worse.
Mine came with a 200mw VTX and carrying case, but I don't think they all do.Really nice little quad to learn flying fpv with. It doesn't require any soldering, just some zip ties to mount the esc and 2 hex drivers to screw it together. The led's are really bright, you could do some night flying with it. A hole for the video tx would have been nice and the props it came with are useless. Do get 5x4 props if you have flown a quad before, on 5x3's it has not much power.
all together it is a real nice quad, especially because you just need a battery and a reciever.I yust umpack my Quad.
It was NOT pre-assembled! So loss point is Quality.
But I got the Video Transmitter and a case, which increase the value, but that was 200mW so not usable in Europe. So value decrees again.
The picture might be usable to build but an wiring diagram should be provided!
Also the Types of the ESC could be described better (could I flash SimonK esC SW?)Mine came with carry case, video camera and TX all was great.
I did have one esc DOA on arrival and replaces the esc's with 4 x afro 12amp's.
fly's great i am still unable to work out the channels on the video TX to connect to my fatshark V2 goggles.
With Gemfan 5x4.5x2 props 1500mha nano tech 9.5 min hover
With Gemfan 5x4.5x2 props 2200mha nana tech 13 min hover
over all i am very pleased and once i rewire the power plug on the main board i will be able to run 6 inch propsThis quad is an amazing buy for the money and is a great first FPV quad. CC3D boards are extremely user friendly to setup through the GCS software if you want to set up your own tune and make adjustments. You would be hard-pressed to find another quad of this quality for the same price, even if you built it yourself.This little quad is a good time! Flies pretty well with the provided 3-blade props, but I have been using the DYS bullnose 5045's which you can buy for about $.50 a pair on HK. Had to do a little tinkering to get it setup with OpenPilot but got it eventually. If your having trouble with the CC3D RX wiring harness, it hooks into the receiver in the same order as it goes into the flight controller. This means it starts with the Motor 1 cable (the black/red/white), then Motor 2 (blue), Motor 3 (Yellow), Motor 4 (Green), then the Aux 1 (Yellow) and Aux 2 (black). You cant load OpenPilot software if the quad is armed (another issue I had). Hope that helps someone!Simplemente genial completo de todo, con su maletin incluido. Las piezas y los motores se ven de buena calidad y todo muy bien acabado, lo recomiendo.Mine just arrived. The description says assembled with a carry case. Mine came unassembled and no carry case.
Be carefull, HK has not been very helpful.